Hatco HWBI-S Series, Installation And Operating Manual, Page: 3 / 40

3 HWBISM-0722
English
IMPORTANT SAFETY INFORMATION
WARNING
ELECTRIC SHOCK HAZARD:
• Unit must be installed by a qualified electrician.
Installation must conform to all local electrical codes.
Installation by unqualified personnel will void unit
warranty and may lead to electric shock or burn, as
well as damage to unit and/or its surroundings.
• Turn OFF power switch, unplug power cord/turn off
power at circuit breaker, and allow unit to cool before
performing any cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• Remote control enclosure must be mounted on vertical
wall and installed in vertical position. Mounting remote
control enclosure in horizontal position may result in
collection of liquids and lead to electric shock.
• Operating voltage of remote control enclosure water valve
exceeds 50 V (extra low voltage). Enclosure is marked
with the following hazard identification symbol:
• Do not use unit to melt or hold ice. Doing so may
cause condensation, creating an electrical hazard and
causing personal injury and/or damage to unit. Damage
caused by condensation is not covered by warranty.
• For non auto-fill units, turn off unit when filling with
water and avoid splashing.
• Do not clean unit when it is energized or hot.
• This unit is not “jet-proof” construction. Do not use
jet-clean spray to clean this unit.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD:
• Install unit with a minimum of 3-1/2″ (89 mm) of space
from bottom of unit to all combustible surfaces to
prevent combustion.
• Unit must be installed using ribbon putty gasket
between unit and installation surface per installation
instructions (refer to Installation section of this
manual).
• Do not use flammable cleaning solutions to clean this
unit.
WARNING
This unit must be installed by qualified, trained installers.
Installation must conform to all local electrical and
plumbing codes. Check with local plumbing and electrical
inspectors for proper procedures and codes.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them
away from unit.
Make sure all operators have been instructed on the safe
and proper use of unit.
Make sure food product has been heated to the proper
food-safe temperature before placing in the unit. Failure
to heat food product properly may result in serious health
risks. This unit is for holding pre-heated food product only.
Hatco Corporation is not responsible for actual food
product serving temperature. It is the responsibility of the
user to ensure food product is held and served at a safe
temperature.
This unit has no “user-serviceable” parts. If service is required
on this unit, contact an Authorized Hatco Service Agent or
contact the Hatco Service Department at 800-558-0607 or
414-671-6350.
CAUTION
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Use caution
when touching these areas.
• Drain water may reach temperatures in excess of 200°F
(93°C). Use appropriate plumbing materials when
installing drain.
• DO NOT clean unit while it contains any food product.
Remove food product and allow unit to cool completely
before cleaning.
Locate unit at proper counter height in an area that is
convenient for use. The location should be strong enough
to support the weight of unit and contents.
Auto-Fill units must be installed with adequate backflow
protection and must conform with all federal, state, and
local codes.
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.