manualshive.com logo in svg

Hart Sceintific DewK 1620, User Manual

Share
Download
Hart Sceintific DewK 1620 User Manual Download Page 109

or

Response: 1,1,25.629,C,29.29,%,2,0,C,0,%,2003,9,16,11,1,42

This command is equivalent to the FETC? command.

8.4.2.17

READ? [<chn>]

Returns a comma delimited list of the most recent measurements for the speci-
fied channel or for both channels.

Example 1: READ? 1

Response: 25.576,29.30

or

Response: 1,1,25.629,C,29.32,%,2003,9,16,11,2,38

Example 2: READ?

Response: 25.582,29.32,26.341,37.96

or

Response: 1,1,25.629,C,29.29,%,2,0,C,0,%,2003,9,16,11,1,42

This command is equivalent to the FETC? command.

8.4.3

Data Commands

The data commands are used to access daily statistics or recorded
measurements.

8.4.3.1

DATa:DSTatistics:ENABle?

Returns the state of the daily statistics recording enable.

Example: DAT:DST:ENAB?

Response: 0

A value of 1 is returned if the daily statistics recording is enabled. A value of 0
is returned if the daily statistics recording is disabled.

8.4.3.2

DATa:DSTatistics:ENABle <bool>

Sets the state of the daily statistics recording.

Example: DAT:DST:ENAB 1

The <bool> parameter turns the daily statistics recording on (1 or ON) or off (0
or OFF). This command may be password protected (see Section 8.4.10, Pass-
word Commands).

102

Hart Scientific

8 Digital Communications Interface

Summary of Contents for DewK 1620































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands