Harry 314, Safety And Operation Instructions, Page: 14 / 60

ENGLAND
HARRY
14
3) ASSEMBLY
Tools:
To assemble the HARRY mower you will need:
- One straight head screwdriver;
- Two small adjustable wrenches.
Deflector-plate assembly (Fig. 02 - Fig. 03 - Fig. 04)
1 ) Position the spring into the two holes of the deflector plate, insert the
rod (1), position the assembled baffle plate on the casing, securing it
with the 2 screws (2).
Assembly of handlebar mod. 313 (Fig. 06)
1 ) Insert the lower plough tails of the handlebar into the relative
slots on the two lateral hubs and tighten the two knobs.
3) Place grille over the two hooks of the catcher. Be sure grille flanges
face mower. Mower side and catcher side are indicated on grille.
4) Place metal plates on frame brackets, just aft of each hook. Secure to
bracket with flat head bolts, nuts and washer. The other end of clip
should now cover the top of the grille, just aft the hook... thus preventing
the grille from falling off when the grille is raised to full open position
at time of emptying grass cuttings.Slip bag top left and right plastic
ends over the metal frame.
5) Attach spoon to lower right from side of grille with 4 straight head
screws and nuts. Tighten with screwdriver and small adjustable wrench.
6) To attach grasscatcher to mower stand on right side of mower lift
deflector with right hand, and with left hand hook catcher onto two
open areas of handle rod.
Assembly of fabric grasscatcher (Fig. 05)
1) Slip the wire frame into the fabric bag, keep the metal handle outside
of the fabric. The metal handle and fabric bag cloth handle will both
be at top side of the catcher. The plastic sheet will be on the bottom .
2) Secure the 4 sides of fabric bag to rectangular frame opening by
slipping plastic ends of bag over the metal frame. Leave top left and
right of bag off.
Wear safety glasses to protect
your eyes
Never smoke while filling the gasoline
tank
Keep persons, who do not know the
safety rules away from the mower.
4) OPERATION
Keep the handle (4) pressed during machine operation. When the handle
is released, the engine stops. For further information and explanations,
read carefully the user instruction manual of the engine. Squeeze adjusting
lever towards wheel and move it to the position desired.
assure pin on adjusting lever (5) engages notch in
housing. Refer to figure for the approximate cutting height afforded by
each of the different positions.
For model
471-C50-C54-P54 it is possible to alter the advance speed
by means of the lever (17) ( Fig. 10 ).
Pre-start inspections
before each start-up, check the following and, if necessary, perform the
service specified.
l CHECK deflector, grasscatcher to make sure they are in proper position
and tightened.
l CHECK oil level in engine and, if necessary, add oil up to, but not
over, full mark.
l CHECK cutting heights and adjust (see paragraph "cutting height
adjustment").
Engine startup (Fig. 07 - Fig. 08 - Fig. 09)
Once the machine has been set up properly, start the engine as follows:
a- Operate the brake handle (4) to enable engine startup.
b-
Engine with PRIMER system: Press the fuel-enrichment pump located
on carburettor 3 or 4 times.If the model is equipped with an accelerator
position the accelerator lever (3) on MAX.
Engine with CHOKE system: If the model is equipped with an
accelerator, when the engine is cold, position the accelerator lever (3)
on START.
c- Start engine: Grip the starting handle (7) and pull the starter rope
gently until you feel the resistance caused by compression. Then give
the starter rope a sharp tug.
ATTENTION! The blade starts turning as soon as the engine
is started.
ATTENTION! The blade will continue turning for max. 3
more seconds after the engine has been stopped.
Engine stop:
The engine and the blade stop when the handle is released.
ATTENTION! Undertake the operation only with the engine
running
5) MOWING PROCEDURE
Mowing procedure:
Vary speed to suit grass conditions. Set the engine speed to the maximum
for tall and thick grass or lower for short and thin grass. On self propelled
models squeeze control bar towards handle to engage the transmission;
to stop forward motion release the control bar. The mower can be hand
pushed with the control released.
Cutting height adjustment (Fig. 11)
To adjust the cutting height on machines with centralized control it is
necessary to grip the lever, lift the sliding sleeve and position to one of the
7 set positions.
Always stop the engine and wait until the mower blade goes
to a complete halt.
Never use the lawn mower without either grasscatcher or
deflector .