Harmonic Drive HFUS-2SH Manual Download Page 47 | Manualshive

Page: 47 / 69

background image

47

Harmonic Drive® Greases

Type

Standard

Special

SK-1A

SK-2

Flexolub®-A1

4B No.2

Operating temperature range

0 °C ... +80 °C

0 °C ... +80 °C

-40 °C ... +120 °C

-10 °C ... +110 °C

Base oil

Mineral oil

Mineral oil

PAO / Ester oil

Synthetic oil

Thickener

Lithium soap

Lithium soap

Lithium soap

Urea

Consistency class (NLGI)

2

2

1

1-2

Base oil viscosity (40 °C; 100 °C)

37; 5.9 mm

2

/St

37; 5.9 mm

2

/St

25; 5.2 mm

2

/St

50; 12 mm

2

/St

Drop point

197 °C

198 °C

180 °C

247 °C

Colour

yellow

green

pale yellow

pale yellow

Max. storage time in hermetically sealed container

5 years

Ease of sealing (safety against grease- or base oil leakage

at the oil seals)

+

+

+/-

+/-

Notes:

+ = Good
+/– = May be critical depending on design / mounting position / application, please contact Harmonic Drive AG

Table 47.1 gives some important information regarding Harmonic Drive® Greases.

Table 47.1

Safety data sheets and technical data sheets for the Harmonic Drive® Greases are available from Harmonic Drive AG.

1021387 12/2018

V02

Precautions for using Harmonic Drive® Grease 4B No.2

Harmonic Drive® Grease 4B No.2 has fluid characteristics (thickness, shear characteristics etc.) suited to Harmonic Drive®
Gears. The following procedures can be utilised to improve the lubricant life:

1) apply the grease to the required areas before operation.
2) remove any abrasion particles after the running-in period.
3) re-grease the contact areas.

Precautions

1) When greasing:

The consistency of Harmonic Drive® Grease 4B No.2 when stored in the container is higher than during operation. However,
please note that the consistency varies depending on the storage period.
Before greasing please mix the grease to soften the consistency.

2) Aging (running-in):

The aging process before the fully loading the gears softens the grease. More effective grease performance can be realised
when the grease flows around the required contact areas of the Harmonic Drive® Gear.

Therefore the following aging method is recommended:
• Keep the internal operating temperature below 80 °C. Do not allow a steep increase in temperature during the aging process.
• Limit the input speed to between 1000 and 3000 rpm. Lower speeds are more effective. Select an input speed as close to
1000 rpm as possible.
• The time required for aging is 20 minutes or longer.
• Keep the output rotation angle as large as possible during the aging process.

Contact our offices if you have any questions about handling Harmonic Drive® Grease 4B No.2.

«
...
45
46
47
48
49
...
»

Summary of Contents for HFUS-2SH






































































Reviews:

No comments

Related manuals for HFUS-2SH

Brand: Yamaha Pages: 7

Brand: Vascat Pages: 60

Brand: BONFIGLIOLI Pages: 16

MTR-DCI-...IO Series

Brand: Festo Pages: 182

Brand: Daedong Pages: 66

Brand: DIMOEL Pages: 8

Brand: Applied Motion Products Pages: 2

Brand: SICK Pages: 20

Brand: Stobag Pages: 12

Brand: Iveco Motors Pages: 60

Brand: Iveco Pages: 206

Brand: Graco Pages: 30

Brand: Wilesco Pages: 4

Brand: Valach Pages: 24

Brand: Chicago Pneumatic Pages: 100

BEVELMASTER 204B

Brand: TRI tool Pages: 46

Brand: Honda Pages: 48

Brand: Honda Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands