Harmonic Drive HFUS-2SH Manual Download Page 3

Page: 3 / 69

1021387 12/2018

V02

Installation and Operation .................................................................................................................50

5.1

Transport and Storage ........................................................................................................................................................ 50

5.2

Gear Condition at Delivery .................................................................................................................................................. 50

5.3

Assembly Information........................................................................................................................................................ 50

5.4

Recommended Tolerances for Assembly SHG-2SO and SHG-2SH ................................................................................... 51

5.5 Lubrication ...........................................................................................................................................................................52

5.6

Assembly Preparation ........................................................................................................................................................ 54

5.7

Decommissioning and Disposal .........................................................................................................60

7. Glossary ................................................................................................................................................61

7.1

Technical Data ..................................................................................................................................................................... 61

7.2

Labelling, Guidelines and Regulations .............................................................................................................................. 68

Summary of Contents for HFUS-2SH






































































Search results

Summary of Contents for HFUS-2SH

Reviews:

Related manuals for HFUS-2SH

Brands by name

Popular brands

Harmonic Drive HFUS-2SH, Manual

Search results

Summary of Contents for HFUS-2SH

Reviews:

Related manuals for HFUS-2SH

Brands by name

Popular brands