background image

AL625 & AL625HD 

 

Page 10 

REV: 1-24-12 

ATTACH LEVELING FEET TO THE TROLLEY ASSEMBLY

 

 

Place the adjusting feet (found in the hardware bag) in the holes of the SIDE MOUNTING RAILS, near the front of 
the Tracker.   

 

If the floor of the vehicle is level all the way, insert the feet with a 3/8 washer on each directly through the mounting 
rail as shown in the figure below.  Secure the mounting feet with a 3/8 washer and Nylock nut on top. 
 
 

 

 
 

If you need to elevate the feet in order to level the trolley assembly, put a 3/8-16 hex jam nut and 3/8 washer onto 
the leveling foot first, then insert the threaded portion of the foot through the side mounting rail, as shown in the 
figure below.   
 
If removing the High threshold Feature you will have to saw off threads of leveling feet to clear platform. 
 

 

 

Turn the additional 3/8-16 jam nut & nylock nut to adjust the height of each leveling foot.  Adjust the height of the 
feet so that the weight of the Trolley Assembly is evenly distributed on both of the mounting bars and leveling feet. 

 

Next- set the final position of the Trolley Assembly in the cargo area and tighten down all of the nuts and bolts. 

 

 
 
 
 
 
 
 
 
STEP 5  

Summary of Contents for AL625HD





























Reviews: