background image

2

  Dry  Seasoned  Wood  Only!                               

TL2.6 Woodburning Stove

Save These Instructions

Harman®  •  TL2.6 Owner's Manual_R25  •  2011 -___  •  09/15

Report #/ Raport #

135-S-30-2, 135-S-30b-6.2

Tested to / Testé à:

 UL 1482-2011, UL 737-2011, ULC-S627-00, EPA Method 28 & 5G

Approved For Use in Mobile/Manufactured Homes (UM) 84-HUD - 

USA ONLY

“PREVENT HOUSE FIRES” 

Install and use only in accordance with manufacturer’s installation 

and operation instructions and local codes. In absence of local codes, installation must meet 

minimum requirements of NFPA 211 in USA. Refer to manufacturer’s instructions and local codes 

for precautions required for passing chimney through a combustible wall or ceiling.

This wood heater needs periodic inspection and repair for proper operation. Consult the owner’s 

manual for further information. It is against federal regulations to operate this wood heater in a 

manner inconsistent with the operating instructions in the owner’s manual.

WARNING: FOR MANUFACTURED HOMES:

 (US Only) Do not install appliance in a sleeping 

room. An outside air inlet must be provided. The structural integrity of the manufactured home’s 

floor, walls, and ceiling must be maintained.

Flue connector pipe must be 6” diameter, minimum 24 MSG blue steel. Chimney must be factory 

built 103HT or masonry construction. Contact Local Building or Fire Officials about restrictions and 

installation inspection in your area.

DO NOT CONNECT THIS APPLIANCE TO A CHIMNEY SERVING ANOTHER APPLIANCE.

FOR USE WITH SOLID WOOD FUEL ONLY, DO NOT bURN COAL.

EPA Certified Emissions: 3.7 g/hr

Fuel Type: 

Cord Wood

DO NOT Overfire - If Heater or chimney connector glows, you are overfiring.

Optional Blower Harman #1-00-856082: Electrical Rating 115 VAC, 60Hz, 1AMP Maximum 

Route power cord away from unit.

OPERATE ONLY WITH DOORS CLOSED

 

Replace glass only with 5mm ceramic, available from your dealer.

Combustible flooring must be protected with an approved 0.45R hearth board.

Appliance must be installed with the legs attached. Do not obstruct airflow under the appliance.

DANGER: Risk of Fire or Explosion - Do not burn garbage,  gasoline, drain oil or other 

flammable liquids.

WARNING: Risk of Fire, Do not operate with fuel loading or ash removal doors open.

Do not store fuel or combustibles within marked clearances. Inspect and clean chimney 

and connector regularly - Under certain conditions of use, creosote buildup may occur 

rapidly.

The Bypass Damper must be opened prior to opening any load or ash door.

Do not install a grate or otherwise elevate the fire.

Maisons approuvé pour utilisation à Mobile / manufacturés (UM) 84-HUD - 

USA SEULEMENT

"Empêcher  MAISON  incendies"

 Installer et utiliser uniquement en conformité avec installation et 

d'utilisation les instructions du fabricant et les codes locaux. En l'absence de codes locaux, l'installation doit 

satisfaire aux exigences minimales de la norme NFPA 211 aux Etats-Unis. Reportez-vous aux instructions 

du fabricant et les codes locaux pour les précautions nécessaires pour faire passer la cheminée à travers 

un mur ou un plafond combustible.

Ce poêle à bois doit inspection périodique et la réparation pour un fonctionnement correct. Consultez le 

manuel du propriétaire pour plus d'informations. Ce est contre les règlements fédéraux pour faire fonctionner 

ce poêle à bois d'une manière incompatible avec les instructions d'utilisation dans le manuel du propriétaire.

AVERTISSEMENT: POUR maisons préfabriquées:

 (États-Unis uniquement) Ne pas installer l'appareil 

dans une chambre à coucher. Une entrée d'air extérieur doit être fournie. L'intégrité structurale du sol, les 

murs et le plafond de la maison préfabriquée doit être maintenue.

Tuyau de raccordement de fumée doit être de 6 "de diamètre, en acier au minimum 24 MSG bleu. 

Cheminée doit être construite l'usine 103HT ou la construction de maçonnerie. Contactez Immeuble Local 

ou fonctionnaires incendie au sujet des restrictions et l'inspection d'installation dans votre région.

NE PAS brancher l'appareil à une cheminée desservant un autre APPAREIL.

Pour une utilisation avec Solid combustible bois Seulement, Ne pas brûler de charbon.

Émissions certifiés EPA: 3,67 g / h

Type de carburant: Cordon bois

NE SURCHAUFFEZ - Si le connecteur chauffe ou de la cheminée rougeoie, vous surchauffez.

Facultatif Blower Harman # 1-00-856082: Note électrique 115 VAC, 60Hz, 1AMP maximum

Route cordon électrique de l'appareil.

FONCTIONNER UNIqUEMENT AVEC LES PORTES FERMéES

Remplacer le verre seulement avec de la céramique 5mm, disponible chez votre revendeur.

Plancher combustible doit être protégé par un conseil 0.45R foyer approuvé.

L'appareil doit être installé avec les jambes attachées. Ne pas obstruer le flux d'air sous l'appareil.

DANGER: risque d'incendie ou d'explosion - Ne pas brûler de déchets, de l'essence, vidanger l'huile 

ou d'autres liquides inflammables.

AVERTISSEMENT:  Risque  d'incendie,  ne  pas  fonctionner  avec  chargement  de  combustible  ou 

d'enlèvement de cendres portes ouvertes.

Ne  pas  stocker  carburants  ou  de  combustibles  dans  les  dégagements  marqués.  Inspectez 

et  cheminée  propre  et  le  connecteur  régulièrement  -  Dans  certaines  conditions  d'utilisation, 

l'accumulation de créosote peut se produire rapidement.

Le Bypass amortisseur doit être ouvert avant d'ouvrir ne importe quelle porte de charge ou de la 

cendre.

Ne pas installer une grille ou autrement surélever le feu.

MODEL / MODÈLE: “TL2.6” Woodburning Stove

Room Heater Solid Fuel Burning Type

SUITABLE FOR MOBILE-HOME INSTALLATION 

(USA ONLY)

352 Mountain House Road

Halifax, PA 17032

ECO: 
PARt # / REv:  3-90-00857_RevD
ORiginAtOR:  Spidle
DAtE:  04/15
LAbEL SizE:  11.5 in. x 6.5 in.
LOCAtiOn: 

Rear of Stove

CLASS: 
ADHESivE: 

468

MAtERiAL: 

MEtAL

ink: bLACk
OvERCOAt:

LAbEL tiCkEt

(4) Hole Size = .187

Corners .062

May be burned as a fireplace with “Cozy Screen” Part# 3-40-06960 in place over door opening. Otherwise, doors must remain closed during operation

Peux fonctionner comme un foyer avec la pièce no. 3-40-06960 ‘’ Cozy Screen ‘’ placée au dessus  de l’ouverture de la porte. Autrement , les portes doivent demeurer fermées durant  le fonctionnement.

US ENVIRONMENTAL PROTECTION AGENCY

Certified to comply with 2015 particulate emission standards. Not approved for sale after May 15, 2020.

Certifié conforme aux normes 2015 d’émission de particules. Non approuvé pour la vente après le 15 mai 2020.

ATTENTION:

CHAUD LORS DU FONCTIONNEMENT- NE TOUCHEZ PAS 

L’APPAREIL-GARDEZ LES ENFANTS ET LES VÊTEMENTS ÉLOIGNÉS- TOUT CONTACT 

PEUT ENTRAÎNER DES BRÛLURES DE LA PEAU. RÉFÉREZ-VOUS À LA PLAQUE 

SIGNALÉTIQUE ET AU MODE D’EMPLOI. GARDEZ LE MOBILIER ET LES AUTRES 

MATÉRIAUX COMBUSTIBLES BIEN À L’ÉCART DE L’APPAREIL.

CAUTION:

HOT wHILE  IN  OPERATION-  DO  NOT  TOUCH- 

kEEP CHILDRENAND CLOTHING AwAy- CONTACT MAy CAUSE SkIN 

BURNS- SEE NAMEPLATE AND INSTRUCTIONS. kEEP FURNISHINGS 

AND OTHER COMBUSTIBLE MATERIALS A CONSIDERABLE DISTANCE 

AwAy FROM THE APPLIANCE

REFER TO PRODUCT MANUAL FOR CLEARANCES WITH ADDITIONAL VENT CONFIGURATIONS.

Veuillez vous référer au manuel d’instruction pour informations additionnels pour la configuration de 

la ventilation.

Floor protection must be a non-combustible material. Must also be 

placed under any horizontal sections of flue connector, extending 

2” (51mm) beyond each side of the connector. / Pour protéger le 

plancher, il faut sous le poêle un matériau. Qui doit aussi être placé 

sous les parties horizontales du tuyau de raccord à la cheminée et 

s’étendre à 51 mm (2 po) au-delà de lateral du tuyau.

When  installed  with  the  optional  leg  kit,  The  bottom  heat  shield 

must be in place, and the area under the appliance kept clear. Que 

installé avec le kit de jambe optionnel, le bouclier de chaleur de 

fond doit être dans l’endroit et la région sous l’appareil gardé clair.

BARCODE LABEL

008

Serial No.

N

o

 de série:

Rev D

P.N. 3-90-00857

Date of Manufacture / Date de fabrication:

2015   2016   2017   JAN   FEB   MAR   APR   MAy   JUN   JUL   AUG   SEP   OCT   NOV   DEC

Manufactured by / Fabriqué par: Hearth and Home Technologies 352 Mountain House Road, Halifax PA 17032

A

 = Unit to Sidewall  

17”

b

 = Unit to Backwall  

17”

C

 = Chimney Connector to Sidewall 

27”

D

 = Chimney Connector to Backwall 

20”

E

 = Unit to Adjacent Wall  

14-1/2”

F

 = Chimney Connector to Adjacent Wall  23”

CLEARANCE TO COMbUSTIbLE SURFACES

A

 = Entre le mur lateral et l’appareil 

432mm

b

 = Entre le mur arriereet l’appareil 

432mm

C

 = Entre le tuyau et le mur lateral 

686mm

D

 = Entre le tuyau et le mur arriere 

508mm

E

 = Entre le mur adjacent et l’appareil 

368mm

F

 = Entre le tuyau et le mur adjacent 

584mm

CLEARANCE TO COMbUSTIbLE SURFACES

D

b

C

A

E

F

Made  in  U.S.A.  of  US  and  imported  parts.  /  Fabriqué  aux  États-Unis-

d’Amérique par des pièces d’origine américaine et pièces importées.

USA

8”

8” (200mm)

CAN 

200mm

18”

457mm

Hearth & Home Technologies welcomes you to our tradition of excellence! By choosing a Harman appliance, you have become 

part of our commitment to meeting the heating needs of consumers with the most distinctive, powerful and responsible home 

heating products available. 
With it's durable steel-body construction, the TL2.6 takes advantage of Harman’s 30+ years of stove design, technology and 

manufacturing. The Firedome Plus secondary combustion system provides for super-clean burning and minimal maintenance. 

The top-loading feature makes for more convenient loading, with enough fuel for an all day burn.
We wish you and your family many years of enjoyment in the warmth and comfort of your hearth appliance.
Thank you for choosing Harman.

This Label is located on the rear of the appliance. It contains important safety test information as well as the clearances to 

combustible materials. The label also contains the appliance serial number. For your records, copy your serial number and 

purchase date here.

Serial #: ________________________  

 

Date of Purchase: ________________________

SAMPLE LABEL

Summary of Contents for TL 2.6













































Reviews: