Heat&Glo 6000C-IPI Owner'S Manual Download | Manualshive

Page: 1 / 85

background image

1

Heat & Glo • 6000C-IPI, 8000C-IPI • 2164-900 Rev. W • 8/14

•

DO NOT

store or use gasoline or other

fl

am-

mable vapors and liquids in the vicinity of this

or any other appliance.

• What to do if you smell gas

-

DO NOT

try to light any appliance.

-

DO NOT

touch any electrical switch.

DO

NOT

use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas suppli-

er’s instructions.

- If you cannot reach your gas supplier, call

the

fi

re department.

• Installation and service must be performed

by a quali

fi

ed installer, service agency, or the

gas supplier.

WARNING: If the information in these

instructions is not followed exactly, a

fi

re

or explosion may result causing property
damage, personal injury, or death.

Owner’s Manual

Installation and Operation

DO NOT DISCARD THIS MANUAL

NOTICE

Installation and service of this appliance should be
performed by quali

fi

ed personnel. Hearth & Home

Technologies suggests NFI certi

fi

ed or factory trained

professionals, or technicians supervised by an NFI
certi

fi

ed professional.

• Leave this manual with

party responsible for use
and operation.

DO NO

T

DISCARD

• Important operating

and maintenance
instructions included.

• Read, understand and follow

these instructions for safe
installation and operation.

In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas

fi

tter.

See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.

WARNING

A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and shall be installed.

HOT GLASS

WILL

CAUSE BURNS.

DO NOT

TOUCH GLASS

UNTIL COOLED.

NEVER

ALLOW CHILDREN

TO TOUCH GLASS.

This appliance may be installed as an OEM
installation in manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer’s
instructions and the

Manufactured Home

Construction and Safety Standard,

Title 24

CFR, Part 3280

in the United States, or the

Standard for Installation in Mobile Homes,
CAN/CSA Z240 MH Series,

in Canada.

This appliance is only for use with the type(s)
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certi

fi

ed kit is used.

Pour demander un exemplaire en français de ce Manuel

du propriétaire, visitez www.heatnglo.com/translations.

Models:

6000C-IPI

6000C-IPILP

8000C-IPI

8000C-IPILP

1
2
3
...
»

Summary of Contents for 6000C-IPI






















































































Reviews:

No comments

Related manuals for 6000C-IPI

Brand: Cadet Pages: 13

Brand: Panadero Pages: 36

Brand: Superior Pages: 12

OUTLAND LIVING FIRECUBE

Brand: FMI Pages: 12

Brand: Valor Pages: 12

Brand: Majestic Pages: 9

Brand: Napoleon Pages: 2

Brand: HomeTech Pages: 6

Brand: Home Decorators Collection Pages: 30

REGENT FRLC EN Series

Brand: Flavel Pages: 31

Brand: Cal Flame Pages: 32

Brand: Heatilator Pages: 88

Brand: barbas Pages: 32

Brand: kozy heat Pages: 35

TRESANTI OD9544-40

Brand: Twin-Star International Pages: 20

Haliburton GDS28P

Brand: Napoleon Pages: 48

Brand: Charlton & Jenrick Pages: 8

ORVIETO MCFP15O

Brand: Dimplex Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands