background image

Harman®  •  PF-120 Owner’s Manual_R3  •  2014 -___  •  10/14

6

3-90-08120c

If  you  expect  that  small  children  or  vulnerable  adults 

may  come  into  contact  with  this  appliance,  the  following 

precautions are recommended:
•  Install a physical barrier such as:

  -  A decorative fire screen.
  -  Adjustable safety gate.

•  Install a switch lock or a wall/remote control with child 

protection lockout feature.

•  Never leave children alone near a hot furnace, whether 

operating or cooling down.

•  Teach children to NEVER touch the furnace.
•  Consider  not  using  the  furnace  when  children  will  be 

present.

Contact  your  dealer  for  more  information,  or  visit:  www.

hpba.org/safety-information.
To  prevent  unintended  operation  when  not  using  your 

furnace  for  an  extended  period  of  time  (summer  months, 

vacations, trips, etc):
•  Unplug furnace from receptacle.

A.  Appliance Safety

WARNING! DO NOT operate furnace before reading and 

understanding operating instructions. Failure to operate 

furnace according to operating instructions could cause 

fire or injury.

General Information 

 

B. Clear Space

WARNING!  RISK OF FIRE! 

Do  NOT  place  combustible 

objects  in  front  or  to  the  sides  of  the  appliance.  High 

temperatures may ignite clothing, furniture or draperies.

NOTICE:

 

Clearances may only be reduced by means 

approved by the regulatory authority having jurisdiction.

WARNING! RISK OF FIRE! 

Keep combustible materials, 

gasoline  and  other  flammable  vapors  and  liquids  clear  of 

appliance.

•  Do 

NOT

  store  flammable  materials  in  the  appliance’s 

vicinity.

•  Do 

NOT

 use gasoline, lantern fuel, kerosene, charcoal 

lighter fluid or similar liquids to start or “freshen up” a fire 

in this heater.

Keep all such liquids well away from the heater while it is in 

use as combustible materials may ignite.

Contact your dealer or Hearth & Home Technologies if the 

barrier is not present or help is needed to properly install one.

HOT SURFACES

Glass  and  other  surfaces  are  hot 

during operation AND cool down.

Hot glass will cause burns.

• 

DO NOT

 touch glass until it is cooled

•  NEVER allow children to touch glass

•  Keep children away

wARNING

!

•  CAREFULLY SUPERVISE children in same room as 

furnace.

•  Do not touch during operation.

High temperatures may ignite clothing or other 

flammable materials.

•  Keep clothing, furniture, draperies and other flammable 

materials away.

Summary of Contents for PF-120



































Reviews: