background image

3

Model No.: 

HK3797

Product Name:

 4 BURNER BBQ WITH SIDE BURNER - For propane (LPG) use only

FOR OUTDOOR USE ONLY. PLEASE READ INSTRUCTIONS CAREFULLY BEFORE 

ASSEMBLING. RETAIN THIS MANUAL FOR FUTURE REFERENCE.

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open BBQ hood.

4. If odour continues, immediately call your 

gas supplier or your local fire department.

PRECAUTIONS

1. Leak test all connections after each tank refill.

2. Never check for leaks with a match or open 

flame.

3. Do not store or use gasoline or other 

flammable vapours and liquids in the vicinity 

of this appliance.

4. The BBQ must not be installed under or on 

any combustible material. Minimum clearance 

from any combustible materials of ALL sides 

of the BBQ is 600mm and 1000mm overhead.

HAZARDOUS FIRE OR EXPLOSION MAY RESULT 

IF INSTRUCTIONS ARE IGNORED.

It is the consumer's responsibility to see that the BBQ is properly 

assembled, installed, and taken care of. Failure to follow instructions in 

this manual could result in injury and/or property damage.

Dimensions 132(W) 56(D) 118.5(H) cm

Summary of Contents for HK3797


































Reviews: