background image

 

5

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 

 

 

 

 

 

 

 
 
 
 
 
 
 
 

 
 
 
 

 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Figure 4 

POL FITTING

INSTALLATION 

LIQUID PROPANE 

1.  Place the Firepit Burner System on a level surface. 
2.  Go to page 2 of the instructions and review the boxed 
area for proper clearance guidelines.     
3.  Make sure tank valve is in the full OFF position. 
4.  Check tank valve features to ensure it has proper 
external mating threads.  (Tank Valve Marked:  USE 
WITH TYPE 1) 
5.  Inspect hose shipped with unit for damage.  Never 
attempt to use damaged or plugged equipment.  See 
your local LP dealer for repairs. 
6.  After inspecting the LP hose shipped with the unit, 
connect the 46-6-6 on the hose to the 41S-6 on the 
burner system.  Tighten fittings using 2 wrenches. 
7.  When connecting the regulator assembly to the tank 
valve, hand tighten the POL Fitting on the hose to the 
female fitting on the tank. 
8.  Locate the hose out of pathways where people may 
trip over it or in areas where the hose may be subject to 
accidental damage. 
9.Open the tank valve fully (counter-clockwise).  Turn the 
on/off valve at the unit on slowly to the on position and 
use a soap and water solution to check all connections 
for leaks before attempting to light the appliance.  If a 
leak is found, turn the tank valve off and do not use the 
appliance until repairs can be made. 
10.  Proceed with log and cinder installation. 
11.

  

Once log installation is complete slowly turn the 

on/off gas valve to the on position while a lit match is at 
the gas opening of the burner system. 

LOG AND CINDER 

INSTALLATION 

Top View of Burner with no Logs or Cinder 

Top Burner Plate

  

Base Plate 

Gas flows out around the edges of 
the top burner plate. 

Top View of Cinder Installation 

Place Cinder on the Base Plate.  Do not put 
Cinder on the Top Burner  Plate. 

Cinder

 

 

CAUTION:  WHEN BURNING THE FIREPIT 
WITH CINDER FOR THE FIRST TIME IT WILL 
POP AND SHOOT OUT.  KEEP AT LEAST 10 
FEET AWAY FROM THE BURNER DURING 
INITIAL BURN IN PERIOD.   

Once burner and 
log installation is 
complete you 
may put a non-
combustible 
exterior (rock, 
brick, etc.) 
around the legs 
of the burner to 
enhance the look 
of the firepit. 

Firepit with Rock Surround 

Summary of Contents for Sierra








Reviews: