Harbor Freight Tools Vulcan Migmax 215 Owner'S Manual & Safety Instructions Download

Page: 41 / 64

Page 9

For technical questions, please call 1-888-380-0318.

Item 63617

SAFETY

MAINTENANCE

BASIC WELDING

WELDING TIPS

SETUP

10-12 Pound Wire Spool Installation:

Remove the Wingnut and Spacer. If
replacing a Spool, remove the old Spool
and all remaining wire from the liners.

7. Place the Spool Adapter over the Spool Spindle

and against the Spool Brake Pad as illustrated.

8. Place the new Wire Spool over the Adapter and

line up pin on Adapter with hole in Spool.

To prevent wire feed problems, set the
Spool so that it will unwind clockwise.

9. Replace the Spacer over the Spool Spindle

and secure Spool in place with the Wingnut.

Notice:

If Wire Spool can spin freely, Wingnut

is too loose. This will cause the welding
wire to unravel and unspool which can
cause tangling and feeding problems.

10. Screw the Spool Knob into the Spool Adapter.

11.

DCEN Direct Current Electrode Negative

Wire Setup for Flux-Cored (gasless) welding:

Remove the two Wingnuts securing the cables.
Connect the Black Ground Cable to the positive (

)

Terminal using the Wingnut.
Connect the Red Cable to the negative (

–

)

Terminal using the other Wingnut.
Make sure the Cable connectors
sit flush in the grooves.

Welder

Wall

Spool

Brake Pad

10-12 lb

Spool

Adapter

10-12 lb Spool Loading

Wingnut

10-12 lb

Wire Spool

Spacer

Spool Spindle

Spool Knob

Wire

must

unwind

in this

direction

DCEN

Flux-Cored (Gasless) Polarity Setup

Summary of Contents for Vulcan Migmax 215

































































Search results

Summary of Contents for Vulcan Migmax 215

Reviews:

Related manuals for Vulcan Migmax 215

Brands by name

Popular brands

Harbor Freight Tools Vulcan Migmax 215, Owner'S Manual & Safety Instructions

Search results

Summary of Contents for Vulcan Migmax 215

Reviews:

Related manuals for Vulcan Migmax 215

Brands by name

Popular brands