background image

 

 

14 

NOTICE TO INSTALLER; THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN 
WITH THE HOMEOWNER 
 
THE INSTALLATION SHALL BE UNDERTAKEN BY A COMPETENT PERSON AND IN 
ACCORDANCE WITH THE INSTALLATION INSTRUCTIONS. 
 
THE METHOD OF CONNECTION AND THE INSTALLATION REGULATIONS IN THE 
COUNTRY WHERE THE APPLAINCE IS INSTALLED SHOULD BE FOLLOWED IF SUCH 
REGULATIONS EXIST. 
 
CHANGE GAS OF ONE FAMILY TO GAS OF THE OTHER FAMILY SHOULD BE 
PERFORMED BY A COMPETENT PERSON. 
 
INSTALLATION  AND  OPERATION  INSTRUCTIONS  FOR  OUTDOOR  BUILT-IN  GAS  FIRE 
BURNER KIT 

 

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may 
result causing property damage, personal injury or loss of life. 
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any 
other appliance. 

 

WHAT TO DO IF YOU CAN SMELL GAS FUMES: 

Turn off the gas supply at the cylinder or main shut off valve of city network gas. 

 

 

Do not try to light any appliance. 

 

Do not touch any electrical switches. 

 

Do not use any phone, (including cellular phones) 

 

Immediately  call  your  gas  supplier  from  a  neighbor’s  phone.  Follow  the  gas  supplier’s 

instructions. 

 

If you cannot reach your gas supplier, call the fire department. 

 

Installation  and  service  must  be  performed  by  a  qualified  installer,  service  agency  or  your  gas 
provider. 

 

WARNING 

WARNING:  Improper  installation,  adjustment,  alteration,  service,  or  maintenance  can  cause 
injury  or  property  damage.  Read  the  installation,  operating  and  maintenance  instructions 
thoroughly before installing or servicing this equipment. 

 

2B

WARNING 

WARNING: FOR OUTDOOR USE ONLY. 

 

3B

WARNING 

DO  NOT  LEAVE  ANY  OUTDOOR  GAS  APPLIANCE  UNATTENDED  WHEN  IN  USE  OR 
HOOKED UP TO A FUEL SUPPLY 

 

4B

WARNING 

DISCONNECT WHEN NOT IN USE AND KEEP OUT OF REACH OF CHILDREN  

 

GENERAL INFORMATION 

 

5B

WARNING 

This appliance shall be used ONLY outdoors in a well- ventilated space and shall NOT be used 

Summary of Contents for 4001BIS/I2 Plus





















Reviews: