background image

 

Valid from: 15.02.2021 / Source: VAM-UM-00551-EN-04   

Despite careful checking, we cannot exclude the possibility of errors in this document and we accept no liability for the information it 

contains. 

 Page 3 

UNPACKING AND CHECKING THE 
PRODUCT 

Perform the following steps once you receive the product: 

If the product packaging is damaged, ask the shipping agent to be present when the product is 
unpacked. If the product is damaged and the shipping agent is not present, ask for an 
inspection by the representative of the shipping agent within 48 hours of delivery and lodge a 
complaint with the shipping agent. The purchaser has sole responsibility for lodging a 
complaint about any damage to the device caused during transport. 

Open the shipping packaging carefully and follow all the instructions specified on the outside. 
Remove all the packaging materials and carefully remove the product from the packaging. 

Retain the undamaged packaging and all the packaging materials for possible onward shipment 
or storage. Check the product and the relevant accessories visually for any physical damage 
such as scratches, loose or broken parts or other signs of damage that might have occurred 
during transport. 

 

 

Summary of Contents for HK S TKV
























Reviews: