Hanna Instruments HI 96715C Instruction Manual Download Page 12

22

23

Recommendations for Users

Before using these products, make sure that they are entirely suitable for your specific application and for the environment in
which they are used.
Operation of these instruments may cause  unacceptable interferences to other electronic equipments, this requiring the operator
to take all necessary steps to correct interferences.
Any variation introduced by the user to the supplied equipment may degrade the instruments' EMC performance.
To avoid damages or burns, do not put the instrument in microwave oven. For yours and the instrument safety do not use or
store the instrument in hazardous environments.

HI 96715 is warranted for two years against defects in workmanship and materials when used
for its intended purpose and maintained according to the instructions.
This warranty is limited to repair or replacement free of charge.
Damages due to accident, misuse, tampering or lack of prescribed maintenance are not covered.
If service is required, contact your dealer. If under warranty, report the model number, date of
purchase, serial number and the nature of the failure. If the repair is not covered by the warranty,
you will be notified of the charges incurred.
If the instrument is to be returned to Hanna Instruments, first obtain a Returned Goods Authorization
Number from the Customer Service Department and then send it with shipment costs prepaid.
When shipping any instrument, make sure it is properly packaged for complete protection.
To validate your warranty, fill out and return the enclosed warranty card within 14 days from the
date of purchase.

Hanna Instruments reserves the right to modify the design, construction and appearance of its
products without advance notice.

• Turn the instrument off by pressing 

ON/OFF

.

• Turn the instrument upside down and remove the battery cover by turning it counterclockwise.

• Extract the battery from its location and replace it with a fresh one.

• Insert back the battery cover and turn it clockwise to close.

To replace the instrument’s battery, follow the steps:

ACCESORIES

REAGENT SET

REAGENT SET

REAGENT SET

REAGENT SET

REAGENT SET
HI 93715-01

Reagents for 100 tests

HI 93715-03

Reagents for 300 tests

OTHER ACCESORIES

OTHER ACCESORIES

OTHER ACCESORIES

OTHER ACCESORIES

OTHER ACCESORIES
HI 96715-11

CAL CHECK

TM

 Standard Cuvettes (1 set)

HI 721310

9V battery (10 pcs.)

HI 731318

Tissue for wiping cuvettes (4 pcs.)

HI 731331

Glass cuvettes (4 pcs.)

HI 731335

Caps for cuvettes

HI 93703-50

Cuvettes cleaning solution (230 mL)

BATTERY REPLACEMENT

WARRANTY

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

 TestEquipmentDepot.com 

Summary of Contents for HI 96715C













Reviews: