background image

MOD. FT04 rev.01                                  

HELP V (use and maintenance) Ed. 3 - updated: 12/2018 

 

12 

– 

 

MAINTENANCE 

 
First check: 1500 km or 3 months 
 

  Check the tightening of the fixing bolts of the platform 

  Check the tightening of screws and bolts of the lifter 

  Check the lubrication of the sliding points 

  Check the connection between the battery and the lifter, paying attention that there are not 

oxidations on the contacts 

  Check the electric board of the system 

  Check the operations of the lifter and the correct working of the limit switches that limit the 

operations 

  Check the working of the emergency system 

  Check the probable mechanic failure of the lifter 

  Check the right working of the actuators, paying attention to backlashes or noises during the 

movements 
Check the right working of the unhook handle of the front half of the platform 

 
Controlli da effettuarsi a 12, 24 mesi e annualmente 

Repeat the check done in the first check. 
 

NOTA BENE: 

After  2  years  go  to  your  usual  Handytech  Centre  to  have  the  system  state  checked  and  to 
replace any parts that need to be replaced. 
When the guarantee ends the maintenance program is at your own discretion, but our advice 
is  to  follow  it  scrupulously  because  neglect  can  cause  system  faults,  problems  and  create 
dangerous situations while driving. 
The device maintenance interventions, both when covered by guarantee and not, are at the full 
charge of the client.

 

WARRANTY: 24 Months 
 

SPACE FOR THE INSTALLER 

Notes of the installer 

Main fuse position 

 

 

Battery master switch position 

 

 

Control unit box position 

 

 
 

Further information 

 

 
 
 

 

Summary of Contents for HELP V















Reviews: