background image

Changing of spare parts

80100172 Handle EvaDrive

Set battery switch OFF. Disconnect battery cable. Remove battery. Detach cover. The cover is secured by pads of velcro. 
Remove Cable entry. Separate cable entry. Detach connectors from control boxes (VR2 box AND ADM-box) Remove 
cable from cover. 

Note

: routing of cables. Remove 2 screws from handle bracket.

Replace Handle including hinge assembly. Replace 2x Screws (K6S M8x16). Adjust handle height. Tighten screws. 
Thread cable through cover and routing them to control boxes. Attach connectors to VR2 and ADM-box (see p. 9). 
Assemble cable entry and adjust cable positions and length. 

Note

: Cable length adjustment is important in relation to 

mast and handle position. Fit cable entry in cover. Reposition the cover and press it into place. Reattach battery and  
battery cable. Important! If a new handle is is fitted, an initial calibration must be performed as follows: 

Make sure the handle is not physically loaded in any way (e.g. handset must not be hangin on the handle)

Start the system by pressing the ON button

The Snail light starts blinking with double beats

Allow the system to initiate until the Snail light stops blinking. This may take up to 10 minutes

Test all basic functions of the drive system. Make sure approximately the same force is needed to initiate  

 

forwards and backwards motion. If not, perform a manual calibration of the system (se page 10 in the user  

 manual).

60900022 Battery Eva Drive

Set battery switch OFF. Detach battery cable. Slide the old battery upwards. If necessary adjust handle position.
Replace with new battery. Gently slide battery back into place. Reattach battery cable and switch ON. Readjust handle 
position.

80100174 Cover leg EvaDrive

Replace cover leg by pressing it into back of leg profile, use LocTite715 glue to fasten the profile.

80100175/176 Cover Eva450Drive/ Cover Eva600Drive

Set battery switch OFF. Disconnect battery cable. Detach cover. The cover is secured by pads of velcro. Remove the 
velcro from base. Cut the new velcro into eight pieces. Attach the bits of velcro to the same place on the base as the old 
ones. Keep them together with their ”twins”.  Detach Cable entry. Remove the emergency stop button by unscrewing 
the plastic retainer on the inside of the cover. 

Note

 routing of cables. Remove and replace cover.

Route cables and fit cable entry into cover. Re-connect cables to control boxes, 4x to VR2 and 1x to ADM-box (see p. 
9). Remove the glue cover from the velcro. Secure the cover by pressing it into place. Re attach battery cable and switch 
ON.

80100196 Emergency stop button EvaDrive

Set battery switch to OFF. Disconnect battery cable. Detach cover. The cover is secured by pads of velcro. Detach Cable 
entry. Remove the emergency stop button by unscrewing the plastic retainer on the inside of the cover. Note routing of 
cables. Detach emergency stop cable connector from control box VR2. Disconnect cables from emergency stop button 
by unscrewing the cable clamp screws. 

NOTE! 

numbers of connection points (no 21, 22). Remove and replace emer-

gency stop button with the new one, re-attach Emergency stop cables to the emergency stop button. Route cables and 
fit cable entry into cover. Re-connect cables to control boxes, 4x to VR2 and 1x to ADM-box (see p. 9). Secure the cover 
by pressing it into place. Re attach battery cable and switch ON.

12

S E R V I C E   M A N U A L System

RoMedic

TM

Summary of Contents for SystemRoMedic EvaDrive





























Reviews: