Hand Held Products Dolphin 7200 User Manual Download

Page: 85 / 179

C H A P T E R 7 U S I N G T H E D O L P H I N 7 2 0 0 H O M E B A S E

Charging Batteries In The Dolphin 7200 HomeBase

CAUTION: Use only the 3.6V battery packs provided by Hand Held Products.

The use of any other battery pack in the Dolphin Terminal will void your

warranty and may result in damage to the Dolphin Terminal or battery.

With the Dolphin HomeBase, you can charge a Dolphin terminal and a spare NiMH

battery pack simultaneously. The HomeBase charges the terminal and the spare battery

pack independently.

When you insert a battery into the Dolphin HomeBase, it charges the battery at the

highest rate possible. The HomeBase uses a charging method that senses when the

battery pack is fully charged and then drops to a trickle charge to keep the battery pack

at full capacity. You do not need to discharge the battery pack before recharging

because this method protects the battery from damage caused by overcharging. A

dead battery will charge to full capacity in approximately three hours.

The Dolphin Terminal can be stored indefinitely in the HomeBase without damage to

the terminal, battery packs, or the HomeBase. Keep the HomeBase plugged in so that

the Dolphin Terminal’s battery pack stays fully charged.

Charging A Dolphin Terminal

Insert a battery pack into the Dolphin Terminal.

Place the terminal, laser engine window up and the LCD visible, in the Dolphin

Terminal Well of the Dolphin HomeBase.

Let it glide down into the well until it stops.

Once the Dolphin Terminal is properly seated, the Charging Main Batt LED on

the HomeBase will be solid GREEN.

N O T E

For maximum battery life,

Hand Held Products

recommends that you deep-

cycle (service) the battery

twice

before initial use

and then, once a month

thereafter.

Summary of Contents for Dolphin 7200




















































































































































































Search results

Summary of Contents for Dolphin 7200

Reviews:

Related manuals for Dolphin 7200

Brands by name

Popular brands

Hand Held Products Dolphin 7200, User Manual

Search results

Summary of Contents for Dolphin 7200

Reviews:

Related manuals for Dolphin 7200

Brands by name

Popular brands