Hand Held Products Dolphin 7200 User Manual Download Page 68

Page: 68 / 179

C H A P T E R 5 D O L P H I N 7 2 0 0 R S - 2 3 2 H A N D H E L D C O M P U T E R

Charging The Battery Through The RS-232 Port

Before initial use, the Dolphin 7200 RS-232 terminal should be charged for 24 hours.

Follow these steps to charge the Dolphin 7200 RS-232 terminal using the RS-232 port:

Plug the adapter into electrical outlet.

Insert a battery pack into the battery well of the terminal.

Insert the micro-DB-9 RS-232 connector on the communication/charging

cable into the micro-DB-9 port on the back of the Dolphin 7200 RS-232

terminal.

Connect the Universal Power Charging Adapter (Part #PS9U-11) into the

adapter end of the communication/charging cable.

Note: The charging

adapter is a regulated 9V power supply and, due to the different connector, cannot be

used with the HomeBase.

For more on maintaining the batteries, see the section on

Maintaining Batteries

Chapter 2.

Sending and Receiving Data

The Dolphin 7200 RS-232 terminal can be connected to a host computer to send and

receive data via the micro-DB9 RS-232 port using the YX.EXE Utility or the Dolphin

File Transfer Program.

Follow these steps to set up the terminal for sending and receiving data:

Insert a battery pack into the battery well of the terminal.

Insert the micro-DB-9 RS-232 connector to the Dolphin communication

(only) cable into the micro-DB-9 port on the back of the Dolphin 7200

RS-232 terminal.

Connect the DB-9 connector to your PC’s serial port.

Run the YX.EXE utility or the Dolphin File Transfer Program.

For more on sending and receiving data using YX.EXE and the Dolphin File Transfer

Program, see the section on Transferring Files to or From Dolphin in Chapter 9.

Summary of Contents for Dolphin 7200




















































































































































































Search results

Summary of Contents for Dolphin 7200

Reviews:

Related manuals for Dolphin 7200

Brands by name

Popular brands

Hand Held Products Dolphin 7200, User Manual

Search results

Summary of Contents for Dolphin 7200

Reviews:

Related manuals for Dolphin 7200

Brands by name

Popular brands