Hand Held Products Dolphin 7200 User Manual Download Page 174

Page: 174 / 179

A P P E N D I X F G S D O S C O M M A N D S

174

SYNC

The

SYNC

command provides a synchronization checkpoint feature that enables a

batch file to flush the file system's buffers to disk before doing something that might

otherwise cause a disorderly shutdown

Syntax:

SYNC

TIME

The

TIME

command displays or changes the system time. If no parameter is specified,

then the current system time is displayed, and the user is queried for the new system time.

If the user just presses the ENTER key, the system time is not changed. If the user

enters a new time, then the system's real-time-clock is updated.

Syntax:

TIME [hh:mm:ss[.hh]]

TRUENAME

The

TRUENAME

command displays the true name and path of a file.

Syntax:

TRUENAME file

TYPE

The

TYPE

command copies the contents of the specified file to standard output

(usually, the screen). If the drive letter is not specified, then the default drive is assumed.

Syntax:

TYPE [drive:][path]filespec

VER

The

VER

command displays the MS-DOS emulation version number, as well as the

version of the Embedded DOS-ROM operating system that is running.

Syntax:

VER

VERIFY

Summary of Contents for Dolphin 7200




















































































































































































Search results

Summary of Contents for Dolphin 7200

Reviews:

Related manuals for Dolphin 7200

Brands by name

Popular brands

Hand Held Products Dolphin 7200, User Manual

Search results

Summary of Contents for Dolphin 7200

Reviews:

Related manuals for Dolphin 7200

Brands by name

Popular brands