background image

 
HAMWORTHY HEATING LTD 

 

SHERBORNE 

 

500001103/E 

11.0

 

COMMISSIONING AND TESTING 

 

For general layout of boiler, refer to Figure 11.1

 

 
11.1 Electrical Installation 

 
Wiring 

MUST

 be checked by a suitably competent 

person. Power supply required is 230 volts 50 Hz 
single phase. An isolator correctly fused at 6A 
should be sited close to the boiler. 
 
Access to the controls is achieved by removing the 
screw on the top of the outer cover and pulling the 
cover away from the wall. The cover is located on 
the wall frame by four ball studs. Connections to the 
boiler should pass through the 2 x 20mm conduit 
connections located at the bottom left hand side of 
the wall frame. The boiler is supplied with a remote 
stop/start circuit for time clock operation. 

Any other 

interlocks, i.e. Pressurisation unit, BEM System 
should be wired in series with the remote stop/
start loop.

 

The site wiring connections are marked with Live, 
Neutral and Earth connections. See Figure 8.12 and 
9.1 for details.  
 

IMPORTANT :- READ THE WARNING NOTE 
REGARDING EXTERNAL VOLTAGES.

  

 

11.2 Gas Installation 

 
For design see 

Section 5: GAS SUPPLY.

 

The whole of the gas installation including the meter 
must be inspected and tested for soundness and 
purged in accordance with the recommendations of 

BS 6891 or IGE/UP/1 & IGE/UP/1A

 as appropriate. 

 

11.3 Water Circulation System 

 
For design see 

Section 8: WATER SYSTEM. 

The system should be thoroughly flushed out with 
cold water without the pump in position. Ensure all 
the valves are open. 
With the pump fitted the system should be filled and 
air locks cleared. Vent the radiators and check for 
leaks. 
If the system is unvented the pressurisation unit 
should not be utilised for the initial filling. This 
should be carried out using a WRC approved double 
check valve and temporary filling loop. In order to 
comply with local Water Authority Regulations, this 
loop must be disconnected when filling is complete. 
Water treatment should not be fed through the 
pressurisation unit unless permitted by the 
manufacturer. Check the expansion vessel cushion 
pressure as detailed by the manufacturer's 
Installer's Guide. 
 

11.4

  

Commissioning The Boiler 

 
Only competent persons registered for working on 
non domestic gas appliances should attempt the 
following: Before attempting to commission any 

boiler, ensure that personnel involved are aware of 
what action is about to be taken and begin by 
making the following checks:- 

1)

 Flueway passages to chimney are clear. 

2)

 Adequate ventilation as per 

Section 7: AIR 

SUPPLY

 exists in the boiler house or compartment/

room.  

3)

 The system is fully charged with water, ready to 

receive heat. All necessary valves are open and the 
pump is circulating water.  

4)

 The pipework and valve arrangement is installed 

to Hamworthy Heating recommendations in such a 
way that water flow rates will be in accordance with 
Figure 2.2.  

5)

 The gas supply pipework is clear of any loose 

matter, tested for soundness and purged to 

BS 

6891 or IGE/UP/1 & IGE/UP/1A

 as appropriate. 

6)

 The condensate discharge is connected to a 

drain. 
 

11.5.1  Boiler Checks Prior to Lighting 

 

NOTE!

 Refer to Figure 2.2. for Natural Gas 

maximum inlet pressure for normal operation. 
 
Information relating to propane firing can be found in 
Appendix ‘A’.  
 

1)

 Ensure the gas supply is connected but turned to 

the "OFF" position. Any unions or fittings are 
correctly tightened and test points are closed. 

2)

 Ensure electricity is connected but switched 

“OFF”. The plug/socket fan & gas valve connections 
are correctly located and that the thermostat bulbs 
are fully inserted into the pocket. Test the operation 
of the temperature limiter by firmly pressing the 
button (in controls fascia.), removing the clip and 
bulb from the pocket and carefully applying a heat 
source to the bulb. The reset button should operate. 
If satisfactory, refit the bulb in the pocket and secure 
with the clip. 

3)

 Check setting of both temperature limiter and 

control thermostat.  The temperature limiter must 
not be set above 100°C maximum. Adjust if 
required, by turning the setting screw in the direction 
±. Set control thermostat to required temperature.  

4)

 With the fascia panel removed and hung on the 

clips, access the terminal connections at the bottom 
of the main PCB. Figure 9.1 shows the correct 
location of incoming wires. Check for correct setting 
of rotary switch ‘SW1’ on the control panel main 
PCB – refer to Figure 8.12 for details. Remove the 
wire link on connector ‘J4’ (black wire) on the PCB 
and insert a multi-meter set to read DC µA.. 

5)

 The Sherborne

 

boiler is fully modulating, with the 

output dependant upon the control thermostat 
demand, hence to achieve max output the system 
must be cold. 

24 

Summary of Contents for Sherborne Series

















































Reviews: