Hamworthy Milborne 500 Series Design Installation, Commissioning And Operating Instructions Download Page 5

Page: 5 / 64

HAMWORTHY HEATING LTD

MILBORNE 500 SERIES

500001130/A

iii

PICTORIAL AND DIAGRAMATICAL DATA

FIGURES

PAGE

Figure 3.1

Basic Dimensions...................................................................................................................... 3

Figure 5.1

Unpacking the Boiler.................................................................................................................. 5

Figure 6.1

Condensate Discharge .............................................................................................................. 6

Figure 6.2

Condensate Discharge .............................................................................................................. 6

Figure 7.1

Pipework Schematic No. 1 ......................................................................................................... 7

Figure 7.2

Pipework Schematic No. 2 ......................................................................................................... 8

Figure 7.3

Single Milborne 502 Pipework Kit ............................................................................................... 9

Figure 7.4

2 x Milborne 502 Pipework Kit .................................................................................................... 9

Figure 7.5

Flow Resistance Graph............................................................................................................ 10

Figure 8.1

Single Milborne 501 Flue Installation......................................................................................... 11

Figure 8.2

Single Milborne 502 Flue Installation......................................................................................... 11

Figure 8.3

Twin Pipe Flue Adaptation Kit................................................................................................... 12

Figure 8.4

Flue Manifold........................................................................................................................... 12

Figure 8.5

Typical Flue Placement Options ............................................................................................... 13

Figure 11.1

External Device Circuit............................................................................................................. 19

Figure 11.2

Pump Wiring Diagram.............................................................................................................. 20

Figure 11.3

Connections to an External Alarm............................................................................................. 20

Figure 11.4

Interlock Circuits ...................................................................................................................... 21

Figure 11.5

Milborne 502 Master - Wiring Diagram...................................................................................... 21

Figure 11.6

Milborne 502 Slave - Wiring Diagram........................................................................................ 22

Figure 12.1

Master Card Emergency Enable............................................................................................... 23

Figure 12.2

Master Card Emergency Enable............................................................................................... 23

Figure 12.3

Master Card Emergency Enable............................................................................................... 23

Figure 13.1

Milborne Multiple Installation..................................................................................................... 24

Figure 13.2

Setting Jumpers, Typical Example............................................................................................ 25

Figure 13.3

Example of Boiler Installation, 7 boiler Modules in same Cascade Sequence.............................. 26

Figure 13.4

Setting Up / Positioning of Room Thermostats .......................................................................... 27

Figure 15.1

Gas Valve Adjustment Points ................................................................................................... 29

Figure 15.2

Gas Inlet Pressure Test Point................................................................................................... 30

Figure 15.3.1

Analysis Point.......................................................................................................................... 30

Figure 15.3.2

LPG Flow Adjustment .............................................................................................................. 30

Figure 15.3.3

Starting the Boiler .................................................................................................................... 30

Figure 15.3.4

Control Panel Modules............................................................................................................ 31

Figure 15.3.5

Master Control Panel Controls, General Overview..................................................................... 31

Figure 15.3.6

LED Positions.......................................................................................................................... 31

Figure 15.3.8

Air Flow Adjustment................................................................................................................. 32

Figure 15.3.11

Gas Flow Adjustment............................................................................................................... 32

Figure 17.1

Control Panel Overview ........................................................................................................... 36

Figure 18.1

Changing Operating Temperature Set-Points............................................................................ 38

Figure 18.2

Entering into Monitor Mode ...................................................................................................... 39

Figure 18.3

User Level Parameters ............................................................................................................ 40

Figure 19.1

Programming Mode / Parameter Lists....................................................................................... 41

Figure 21.2

Gas Valve Air Inlet Positions .................................................................................................... 51

Figure 21.3

Venturi / Gas Valve Positions ................................................................................................... 52

Figure 21.4

Removing Venturi from Gas Valve............................................................................................ 52

Figure 21.5

Venturi Separated.................................................................................................................... 52

Figure 21.6

LPG Orifice Location................................................................................................................ 52

Figure 21.7

LPG Orifice Fitted .................................................................................................................... 52

Figure 21.8

LPG Orifice Options................................................................................................................. 53

Summary of Contents for Milborne 500 Series

































































Search results

Summary of Contents for Milborne 500 Series

Reviews:

Related manuals for Milborne 500 Series

Brands by name

Popular brands

Hamworthy Milborne 500 Series, Design Installation, Commissioning And Operating Instructions

Search results

Summary of Contents for Milborne 500 Series

Reviews:

Related manuals for Milborne 500 Series

Brands by name

Popular brands