Hamworthy Milborne 500 Series Design Installation, Commissioning And Operating Instructions Download | Manualshive

Page: 34 / 64

background image

HAMWORTHY HEATING LTD

MILBORNE 500 SERIES

500001130/A

28

Wiring connections

Connect the wires from the boiler Master controller
to terminal 1 & 2 of the programmable room
thermostat.

For high temperature heating circuit, terminal 9 at
the Master control provides the live and should be
wired to terminal 1 at the thermostat. Terminal 10 at

the Master control receives the switch live return
and should be wired to terminal 2 at the thermostat.

For low temperature heating circuit, terminal 11 at
the Master control provides the live and should be
wired to terminal 1 at the thermostat. Terminal 12 at
the Master control receives the switch live return
and should be wired to terminal 2 at the thermostat.

For programming details please refer to the instructions provided with the room thermostat. Alternatively contact
Hamworthy Heating Ltd for a copy of instruction manual.

«
...
32
33
34
35
36
...
»

Summary of Contents for Milborne 500 Series

































































Reviews:

No comments

Related manuals for Milborne 500 Series

Brand: RBI Pages: 44

Brand: Navien Pages: 147

Brand: Navien Pages: 4

Brand: Navien Pages: 151

Brand: Navien Pages: 135

Brand: Navien Pages: 155

Brand: Laars Pages: 36

Brand: U.S. Boiler Company Pages: 176

Brand: Beretta Pages: 48

Brand: Radijator Pages: 83

Brand: Unical Pages: 56

Brand: Blodgett Pages: 2

Brand: Bryant Pages: 20

Brand: Rapido Pages: 36

DEVYL 11 D ie FF

Brand: sylber Pages: 92

Ultrastore Rapid GE

Brand: Truma Pages: 8

Brand: Truma Pages: 16

Brand: Potterton Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands