Hamworthy Milborne 500 Series Design Installation, Commissioning And Operating Instructions Download Page 40

Page: 40 / 64

HAMWORTHY HEATING LTD

MILBORNE 500 SERIES

500001130/A

16.2 Burners in Permanent Lock-Out.

In case of permanent lockout of the burners, it is necessary to press RESET (S1)

If you press RESET (S1)

while you are in ‘functioning display mode’ all boiler modules will be reset.

If you press RESET (S1)

while you are displaying the error which caused the permanent lock-out,

only the boiler module involved will be reset.

16.3 Master Panel Permanent Errors, A Errors (permanent lock-out)

Display Nr

PC Nr

Error

Description

RAM_ERROR

Ram check in processor isn’t correct

A16

E2PROM_ERROR

E2prom contents are incorrect

A18 12

WRONG_EEPROM_SIGNATURE

E2prom

doesn’t correspond to main processor

A24 19

STACK_ERROR

Overflow in internal stack

16.4 Master Panel Blocking Errors, E errors (automatic reset)

The following blocking error numbers are possible:

Display Nr

PC Nr

Error

Description

E25 0

E2PROM_READ_ERROR E2prom

isn’t

readable

E23 28

REFHI_TOO_LO_ERROR Temperature measurement is incorrect

E24

REFHI_TOO_HI_ERROR

Temperature measurement is incorrect

E25

REFLO_TOO_LO_ERROR

Temperature measurement is incorrect

E26 31

REFLO_TOO_HI_ERROR Temperature measurement is incorrect

E32 33

NO_SLAVES_PRESENT There are no slaves connected

E34

50HZ_ERROR

Main frequency is not 50Hz (NI)

T_FLOW_1_OPEN

Flow sensor is not connected

E18

T_FLOW_1_SHORTED

Flow sensor is shortened

E20 69

T_TANK_SHORTED

Tank sensor shortened

T_FLOW_2_OPEN

Flow_2 sensor (low sys) not connected

T_TANK_OPEN

Tank sensor not connected

E19

T_FLOW_2_SHORTED

Flow_2 sensor (low sys) shortened

E21 66

NTC4_SHORTED
(NTC4: OUTDOOR T)

Outdoor temperature sensor shortened

Summary of Contents for Milborne 500 Series

































































Search results

Summary of Contents for Milborne 500 Series

Reviews:

Related manuals for Milborne 500 Series

Brands by name

Popular brands

Hamworthy Milborne 500 Series, Design Installation, Commissioning And Operating Instructions

Search results

Summary of Contents for Milborne 500 Series

Reviews:

Related manuals for Milborne 500 Series

Brands by name

Popular brands