Hampton
®
H25-1 Direct Vent Freestanding Gas Stove
37
AUTOMATIC
CONVECTION
FAN OPERATION
The fan operates automatically - turn the knob
at the top right rear corner to adjust to the de-
sired speed. The fan will turn on as the stove
comes up to operating temperature. After the
unit has been turned off and the unit cooled to
below a useful heat output range the fan will
shut off automatically.
ADJUSTING FLAME
HEIGHT
Your heater has an adjustable fl ame to tailor the
look and heat output to your specifi c needs. It
is adjusted by turning the fl ame adjustment dial
on the gas control valve.
Turn clockwise to adjust the fl ame higher, coun-
terclockwise for a lower fl ame.
OPERATING INSTRUCTIONS
OPERATING
INSTRUCTIONS
1)
Read and understand these instructions
before operating this appliance.
2)
Check to see that all wiring is correct and
enclosed to prevent possible shock.
3)
Check to ensure there are no gas leaks.
4)
Make sure the glass in the door frame is
properly positioned. Never operate the ap-
pliance with the glass removed. Never strike
the glass.
5)
Verify that the venting and cap are unob-
structed.
6)
Verify log placement. If the pilot cannot be
seen when lighting the unit - the logs have
been incorrectly positioned.
7)
The unit should never be turned off, and on
again without a minimum of a 60 second
wait.
windows to ventilate the room for a couple of
hours. The glass may require cleaning.
DO NOT ATTEMPT TO CLEAN THE GLASS
WHILE IT IS STILL
HOT
!
Note: When the glass is cold and the appli-
ance is lit, it may cause condensation
and fog the glass. This condensation
is normal and will disappear in a few
minutes as the glass heats up.
DO NOT BURN THE APPLIANCE
WITHOUT THE GLASS FRONT IN
PLACE.
During the fi rst few fi res, a white fi lm
may develop on the glass front as part
of the curing process. The glass should
be cleaned or the fi lm will bake on and
become very diffi cult to remove. Use a
non-abrasive cleaner and NEVER clean
the glass while it is hot.
located at the top right hand corner (rear) of
the stove.
2)
Turn gas control knob so indicator points
to "OFF" position and allow 5 minutes for
any gas in the combustion chamber to
escape.
3)
Turn gas control knob counterclockwise
so indicator points to the "PILOT" position.
Depress the gas control knob fully. Depress
the igniter button several times until the
pilot lights. After approximately one minute,
release the gas control knob. The pilot fl ame
should continue to burn. If the pilot does not
remain lit, repeat operation allowing a longer
period before releasing gas control knob.
4)
When the pilot stays lit, turn the gas knob
further counterclockwise to the "ON" posi-
tion.
5)
Use the thermostat or remote control to turn
on the unit.
6)
Rotate the fl ame height regulator to adjust
the fl ame height higher or lower.
SHUTDOWN
PROCEDURE
1)
Use the thermostat or remote control to turn
off the main burner.
2)
Turn the main gas control clockwise to the
"OFF" position to turn off the pilot (push
knob in slightly).
3)
Turn off all electric power to appliance if
service is to be performed.
FIRST FIRE
The
FIRST FIRE
in your stove is part of the
paint curing process. To ensure that the paint is
properly cured, it is recommended that you burn
your fi replace for at least four (4) hours the fi rst
time you use it with the fan on. When fi rst oper-
ated, the unit will release an odour caused by the
curing of the paint and the burning off of any oils
remaining from manufacturing. Smoke detectors
in the house may go off at this time. Open a few
LIGHTING
PROCEDURE
IMPORTANT: Gas on/off knob cannot be
turned from "PILOT" to "OFF" unless it is
partially depressed.
1)
Turn stove OFF using the Burner "ON/OFF"
switch remote or thermostat. Switches are
IMPORTANT
To ignite or reignite the pilot,
the door to the fi rebox must
be opened.
Only when the pilot holds, without pressure
being applied to the control knob, should the
door to the fi rebox be closed. The unit
must
never
be operated with the glass or door
open.
NOTE: For all propane units and units
equipped with electric spark boxes, see
"Copy of Lighting Plate Instructions" sec-
tion for more details.
