manualshive.com logo in svg

Hamlet Wireless Access Point 150, User Manual

Share
Download
Hamlet Wireless Access Point 150 User Manual Download Page 171

Wireless Access Point 

HNW150AP 

User Manual 

171 

TCP/IP

 

Transmission Control Protocol/Internet Protocol 

The basic protocols used on the Internet. TCP is responsible for 

dividing data up into packets for delivery and reassembling them at the 

destination, while IP is responsible for delivering the packets from 

source to destination. When TCP and IP are bundled with higher-level 

applications such as HTTP, FTP, Telnet, etc., TCP/IP refers to this 

whole suite of protocols.

 

Telnet

 

An interactive, character-based program used to access a remote 

computer. While HTTP (the web protocol) and FTP only allow you to 

download files from a remote computer, Telnet allows you to log into 

and use a computer from a remote location.

 

TFTP

 

Trivial File Transfer Protocol 

A protocol for file transfers, TFTP is easier to use than File Transfer 

Protocol (FTP) but not as capable or secure. 

TKIP 

Temporal Key Integrity Protocol (TKIP) provides WPA with a data 

encryption function. It ensures that a unique master key is generated for 

each packet, supports message integrity and sequencing rules and 

supports re-keying mechanisms.  

triggers

 

Triggers are used to deal with application protocols that create separate 

sessions. Some applications, such as NetMeeting, open secondary 

connections during normal operations, for example, a connection to a 

server is established using one port, but data transfers are performed on 

a separate connection. A trigger tells the device to expect these 

secondary sessions and how to handle them. 
Once you set a trigger, the embedded IP address of each incoming 

packet is replaced by the correct host address so that NAT can translate 

packets to the correct destination. You can specify whether you want to 

carry out address replacement, and if so, whether to replace addresses 

on TCP packets only, UDP packets only, or both. 

twisted pair

 

The ordinary copper telephone wiring used by telephone companies. It 

contains one or more wire pairs twisted together to reduce inductance 

and noise. Each telephone line uses one pair. In homes, it is most 

often installed with two pairs. For Ethernet LANs, a higher grade called 

Category 3 (CAT 3) is used for 10BASE-T networks, and an even 

higher grade called Category 5 (CAT 5) is used for 100BASE-T 

networks. See

 10BASE-T, 100BASE-T, Ethernet

. 

unnumbered interfaces 

An unnumbered interface is an IP interface that does not have a local 

subnet associated with it. Instead, it uses a 

router-id

 that serves as the 

source and destination address of packets sent to and from the router. 

Unlike the IP address of a normal interface, the router-id of an 

unnumbered interface is allowed to be the same as the IP address of 

another interface. For example, the WAN unnumbered interface of 

your device uses the same IP address of the LAN interface 

(192.168.1.254). 

 

The unnumbered interface is temporary – PPP or DHCP will assign a 

‘real’ IP address automatically. 

upstream

 

The direction of data transmission from the user to the Internet.

 

VC

 

Virtual Circuit 

A connection from your DSL router to your ISP.

 

VCI

 

Virtual Circuit Identifier 

Together with the Virtual Path Identifier (VPI), the VCI uniquely 

identifies a VC. Your ISP will tell you the VCI for each VC they provide. 

See

 VC

.

 

VPI

 

Virtual Path Identifier 

Together with the Virtual Circuit Identifier (VCI), the VPI uniquely 

Summary of Contents for Wireless Access Point 150













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands