background image

9

34000 Autry Street, Livonia, MI 48150  |  800.968.5530  |  Fax 734.419.0209  |  www.hamiltonengineering.com  |  LIT91110 REV 06/2018

CONFIGURATION #4

Configuration #4 – CASCADE BOILERS (NO DOMESTIC HOT WATER)

 

• In this configuration an external sensor MUST be connected to terminals 1 & 2 (or 3 & 4, 28 & 29 depending 

 

  on model) on the 

LEAD BOILER ONLY

 and be positioned to sense common loop temperature (after/at low 

 

  loss header).

 

• A room thermostat is to be connected to terminals 5 & 6 (or 13 & 14, 57 & 58 depending on model) of the 

 

  

LEAD BOILER ONLY

. If no yellow jumper wire is attached to terminals 5 & 6 (or 13 & 14, 57 & 58 depending 

 

  on model), which will be removed to connect room thermostat, additional wiring is required. Consult factory.

 

In this configuration the following can be done: 

 

   1. Adjust the boiler minimum and maximum temperature setting via the potentiometer, within the range of

 

       50 - 192°F 

(Parameter 2 EB, 2 EA)

 

   2. Pump P3 can be controlled based on the Room Thermostat, must add heating harness WRE74090 and 

 

       wire to P3 leads. 

Caution: maximum available wattage for external load on the FMT 914 control 

 

       board is 550 watts. If pumps P1 & P3 total less, they both can be powered directly off the board. If 

 

       not, a relay (240v coil) must be used for pump P3.

 

It is important to set the red potentiometer wheel to the desired setpoint on the Lag boilers with the power off to 

 

the Lead boiler. This way, in the event of a control or power failure to the Lead boiler, the Lag boilers will 

 

operate at the desired temperature.

 

BPD

8/10/09

1/2"=1'

Dwg. By:

34000 Autry
Livonia, MI 48150

PH: (800) 968-5530
Fax: (734) 419-0209

Description:

Date:

Scale:

Customer:

HAMILTON

ENGINEERING

Dwg. 
No.:

Checked. 
By:

Pump 1

Pump 1

Pump 1

Zone
Load

Pump 3

Low Loss Header

S3
(Cascade)

Lead

Lag 1

Lag 2

0-10 VDC

(Optional)

Room
Thermostat

Outside Wall

S6

Outside Sensor

(Optional)

Cascade Boiler

With External Sensor

No Domestic Hot Water

Required parameter changes

from base program

Default

Change to

Base Program - HXXXKPCO.pia

All Lag Heaters - 2CA

5

2

All Lag Heaters - 2IA

0

1 - 7

Summary of Contents for EVO 129-599






















Reviews: