background image

34000 Autry Street, Livonia, MI 48150  |  800.968.5530  |  Fax 734.419.0209  |  www.hamiltonengineering.com  |  LIT91110 REV 06/2018

Hamilton Engineering

EVO 129–599

FMT-914 Control Configurations

Do not store or use gasoline or other 

flammable vapors and liquids in the vicinity 

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance

• Do not touch any electrical switch

• Do not use any phone in your building

Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier 

instructions. If you can not reach your gas 

supplier, call the fire department.

If the information in this manual 

is not followed exactly, a fire or 

explosion may result causing 

property damage, personal 

injury or death.

   WARNING

New York   

Massachusetts 

 

SCAQMD   

     CEC Listed

MEA 425-05-E        

Boilers:  G1-06-06-24A         

Compliant Rule1146.2         California Energy Commission

                              

Heaters: G1-06-06-24B                                    

ANSI STD Z21-13/Z21.13A

Certified to CSA 4.9-2004

ANSI STD Z21.10.3/Z21.10.3.b

Certified to CSA 4.1-2004, add.A,B

    WARNING

These appliances MUST be installed by a properly licensed individual in the City and State which the 

unit is being installed. All start up adjustments and subsequent service work must be done by a similarly 

licensed contractor or a factory trained service individual. Failure to comply could result in loss of 

warranty and or severe personal injury, death and or substantial property damage. 

These instructions 

are required to be kept with the appliance on the left side, in the pocket provided.

ANSI Z21.13-2014/CSA 4.9-2014 

UL 795-2011/CSA 3.4 

SCAQMD 1146.2

Summary of Contents for EVO 129-599






















Reviews: