background image

2

1. 

Read all instructions.

2. 

This appliance is not intended for use by 

persons with reduced physical, sensory, or 

mental capabilities, or lack of experience 

and knowledge, unless they are closely 

supervised and instructed concerning use 

of the appliance by a person responsible for 

their safety.

3. 

This appliance is not to be used by children. 

Close supervision is necessary when any 

appliance is used near children. Children 

should be supervised to ensure that they do 

not play with the appliance.

4. 

Never let the vacuum sealer run unattended. 

Disconnect the vacuum sealer from the 

power source before leaving the work area.

5. 

To protect against risk of electric shock, do 

not immerse cord, plug, or vacuum sealer in 

water or other liquid.

6. 

To reduce the risk of electric shock and 

injury to persons, disconnect from power 

supply when not in use, before cleaning and 

before servicing.

7. 

To provide continued protection against 

risk, do not operate any appliance with a 

damaged supply cord or plug, or after the 

appliance malfunctions or has been dropped 

IMPORTANT SAFETY INSTRUCTIONS

WARNING –

 

When using electrical appliances, basic safety precautions should 

always be followed to reduce the risk of fire, electric shock, and/or injury to persons, 

including the following:

or damaged in any manner. Supply cord 

replacement and repairs must be conducted 

by the manufacturer, its service agent, or 

similarly qualified persons in order to avoid 

a hazard. Call the provided customer service 

number for information on examination, 

repair, or adjustment.

8. 

The use of accessory attachments not 

recommended by the appliance manufacturer 

may cause injuries.

9. 

Do not use outdoors.

10. 

Do not let cord hang over edge of table or 

counter, or touch hot surfaces, including 

stove.

11. 

Do not disassemble this appliance beyond 

instructions provided. Doing so may result in 

personal injury.

12. 

Do not place on or near a hot gas or electric 

burner, or in a heated oven.

13. 

Do not use for other than intended purpose.

14. 

This appliance is designed for a maximum 

vacuum ON time of 60 seconds and a 

minimum OFF time of 10 seconds between 

cycles. Stop the appliance and allow it to cool 

to ambient temperature if the appliance has 

been in use for 60 minutes.

15. 

This appliance is for commercial use only.

SAVE THESE INSTRUCTIONS

Vacuum Sealer Safety

w

WARNING

Electrical Shock Hazard

Plug into a grounded outlet.
Do not remove ground.
Do not use an adapter.
Do not use an extension cord.
Disconnect power before cleaning, 

assembling, or disassembling.
Failure to follow these instructions can  

result in death, fire, or electrical shock.

IMPORTANT: This operation manual should be reviewed with all equipment operators as part of your 

operator training program.

w

WARNING

Burn Hazard

Seal bar is hot. Avoid touching it. 
Allow unit to cool 10 seconds before making or 

vacuum-sealing another bag. 
Never open the lid during use. 

Summary of Contents for HVC254

































Reviews: