manualshive.com logo in svg

Hali-Brite L-807, Installation And Maintenance Manual, Page: 10 / 51

Share
Download
Hali-Brite L-807 Installation And Maintenance Manual Download Page 10

Safety Precautions

 

 

 

Proper Usage

 

 

Always use this equipment as specified in this manual. Improper usage may 
result in serious personal injury, property damage, or possible death. 

 

• 

Do not modify any equipment that has not been recommended by Hali- 

Brite

®

. 

• 

Do not use any replacement parts that are not purchased from Hali-Brite

®

. 

• 

Hali-Brite

®

 cannot be responsible for injuries or damages resulting from non- 

standard, unintended applications of its equipment. This equipment is 
designed and intended only for the purpose described in this manual. Uses 
not described in this manual are considered unintended uses and may result 
in serious personal injury, death, or property damage. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

10 

L-807 and L-806 Wind Cone Installation and Maintenance Manual

 

 
 

Summary of Contents for L-807




















































Reviews:

No comments