background image

Step 1:  Install the screen door as normal.  The 
stabilizer bar kit can either be installed at the same 
time as the pet door or can be retrofitted to an existing 

pet door.  If it is being installed at the time of the 
screen door installation, we recommend leaving some 
excess screen mesh material during installation.  It can 
be trimmed after the stabilizer bar installation is 

complete. 
 

 
Step 2:  Measure the width of the screen door from 
the side containing the screen spline.  This 
measurement should be the visible opening between 

the screen frames. 
 
Step 3:  Using this 
measurement, measure 

and mark this distance on 
the stabilizer bar. 
   

 

Step 4:  Cut the stabilizer bar to the proper length.  It is 
easiest to accomplish this with a hacksaw.  After you 
cut the bar to length, make sure you de-burr your cut 
to allow the aluminum clip to fit in properly.  Test fit the bar to the screen door 

frame to check for proper width.  Re-cut the bar shorter if needed. 
 
Step 5:    On  the  side  of  the  screen door containing 
the pet door, with a screwdriver, carefully pull a 

short amount of screen spline out of the screen 
spline frame or raceway directly above the pet door.  
Repeat the process on the other side of the screen 

door frame at approximately the same height above the pet door.  Take care 
not to scratch the finish of the screen door or poke a hole in the screen mesh 

fabric when removing the screen spline.  Also do not pull out too long a 
distance  of  screen  spline  as  it  will  be  more  difficult  to  push  back  in  place 
later. 

 

 
 
Step 6:  Making sure that both clips face the 
correct direction to fit over the screen door 

raceway, carefully slide one aluminum clip into 
each end of the spreader bar.  Take care not to 
push them too far into the spreader bar or 
there may not be enough clearance for the 

raceway. 
 
 
 

Summary of Contents for PET DOOR












Reviews: