Halcro DM8 Owner'S Manual Download Page 13

 

 

  

 Page 13 of 26 

TM

  

dm8 

 

Connections 

Connecting to a power amplifier 

 

Each dm8 has:  

2 pairs of unbalanced current outputs.  1 pair is used in un-bridged mode and both are used 

for driving bridged amplifiers, 2 pairs of unbalanced voltage outputs and 2 pairs of balanced 

voltage outputs. Select the method you wish to operate your power amplifiers in, and connect 

the 2 units using high quality cables.   

 

Outputs are color coded: 

Po, Right  channel (Red Bezel). 

Negative -, Left  channel (White Bezel). 

 

The dm8 will control power amplifiers from balanced and unbalanced voltage sources, as well 

as an unbalanced current source. The dm8 will also control power amplifiers in bridged pair 

configuration.    Custom  made  cables  are  required  to  run  bridged  power  amplifiers  from  the 

balanced Voltage Output. (Fig 7). 

 

Comments on the different dm8 Outputs 

 

The balanced voltage outputs or current-mode outputs are most desirable for minimising earth 

loop generated mains hum and ripple, or high frequency interference if they are a problem. 

Earth loop generated mains hum and ripple, or high frequency interference should not be a 

problem unless the source equipment is poorly designed. 

 

Power Amplifiers with current-mode inputs are rare and are most likely to have an RCA input 

socket. The advantages of this are: 

Ÿ 

Earth loop generated mains hum and ripple are minimized.  

Ÿ 

Cable,  plug  and  socket-generated  interference  is  minimized  (from  poor  connections 

which may be affected by sound vibration for example). 

 

The unbalanced output is quite satisfactory so long as earth loop generated mains hum and 

ripple are not a problem. 

Figure 7 

 

Summary of Contents for DM8



























Reviews: