background image

1

Control
card

Card chain

®

Heat resistant pad

Iron holder

Tip tray

Hakko 912
Soldering iron

Hakko 942
Soldering station

Power cord

1. PACKING LIST

Hakko 942 soldering station

........................... 1

Hakko 912 soldering iron

................................ 1

Power cord ...................................................... 1
Control card .................................................... 1
Heat resistant pad ........................................... 1
Iron holder ....................................................... 1

Tip tray ............................................................ 1
Cleaning sponge ............................................. 1
Instruction manual

.......................................... 1

Card chain ....................................................... 1
Tips (not included)

2. SPECIFICATIONS

Power consumption

Temperature range

Temperature stability

 Hakko 942 soldering station

Power consumption

Tip to ground resistance

Tip to ground potential

Length, less cord

Weight, less cord

Length of cord

70 W (24 V)

< 2 

< 2 mV

172 mm with 2.4D tip

30 g with 2.4D tip

1.2 m

 Hakko 912 soldering iron

Output

Dimensions 
(l 

×

 w 

×

  h)

Weight

24 V

188 

×

 100 

×

 106 mm

 
2,500 g

 Station

NOTE:

The  temperatures  were  measured  using  the  Hakko  191 
thermometer.
This product is protected against electrostatic discharge.
Specifications  and  design  are  subject  to  change  without 
notice.

           

Summary of Contents for 942





















Reviews: