background image

6

Operation

Solder will be fed by pressing the feed switch (or foot switch).

MODE

AUTO MODE

If you press the feed switch, solder will be fed with set time

and speed independently of length of pressing time.

MANUAL MODE

Solder will be fed with set speed during pressing the feed

switch.

Setting for Feeding Time
and Speed

Set the speed before the time. For the setting speed, both

AUTO

 & 

MANUAL

 are effective, but only 

AUTO

 is effective

for setting time.

Adjustment for the
Amount of Solder
Return

After feed solder, specific length of solder can be returned.

This solder return function permits use for simple robots.

Amount of solder return is adjustable within 0~13 mm

(0~0.51 in.). Solder should be rolled back if the amount of

solder return is bigger than the amount of solder feed. Please

set the amount of solder return as small as possible. If the

tip of the returning solder reaches to the guide pipe, flux will

easily accumulate at this point. Be sure that it will not happen.

Insert a driver into a adjustment hall on the side of the station.

Turn left for smaller and turn right for bigger amount.

Adjustment of Tension

When adjust the tension, be sure that not the gear to be

slipped during feed solder, or do not force to feed solder

slipping gear when solder clog.

Set the tension gear loosely for fine solder ( 0.6mm, 0.8mm/

0.024 in., 0.031 in.). Refer to the following chart.

Solder Dia.

   0.6mm

maximum

   1.0mm

14mm

   1.6mm

10mm

Summary of Contents for 373
















Reviews: