background image

1

Precautions

 CAUTION

Setting up should be done while the soldering iron is cool, or you may get burnt.

Do not force the guide pipe bend or turn as this may result in damage.

Do not operate with tube bending or holding in sharp angle. It may cause to clogging.

Input of switching is no-voltage input. Do not apply voltage to the jack for switch.

Periodically, remove the guide pipe and clean out clogged flux.

Do not force the adjustment screw to adjust the amount of solder return. It may cause to damage.

If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualified person in order to avoid personal injury or damage to the unit.

Specifications

Usable Solder

Usable solders are as follows. Some of the parts should be changed according to the diameter of

solder desired to use.

(mm)

(inch)

0.6, 0.65, 0.8, 1.0, 1.2, 1.6 

0.024, 0.025, 0.031, 0.039, 0.047, 0.063

Maximum quantity of usable solder is 1 kg (2.2 pounds).

Dia. of

solder

Usable Soldering Iron

Soldering Iron

HAKKO 900M (For HAKKO 926, 927, 928)

HAKKO 900L (For HAKKO 926, 927, 928)

HAKKO 902 (For HAKKO 931)

HAKKO 903 (For HAKKO 939)

HAKKO 904 (For HAKKO 929)

HAKKO DASH

HAKKO MACH-

I

HAKKO 907 (For HAKKO 936, 937)

HAKKO 908 (For HAKKO 936, 937)

 Remarks

Operationable only with Foot Switch

Specifications

Power Consumption

Motor Rate

6 W

DC 24 V 3.2W

0~7 sec. 

4.5~26 mm (0.14~1 in.)/sec.

0~182 mm (0~7.2 in.) 

0~5 mm (0~0.2 in.) (Fixed Speed)

107(W) x 110(H) x 215(D)

Approx.1.5 kg/3.3 pounds

Solder Feed Time 

Solder Feed Speed

Solder Feed Quantity

Solder Return Quantity

Outer Dimensions 

Weight

Summary of Contents for 373
















Reviews: