background image

4

3. Setting the Tube Unit

The tube is double structure. Insert the inside tube into the

hole of the connection, and the outside black tube should

fully cover the screw part of the connection. Be sure that not

to bend the tube.

(a) Attach the Tube to Guide Pipe

Asse’y.

(b) Set the Attachment on the

Handle of Soldering Iron.

NOTE

The Attachment is not necessary if you use HAKKO

MACH-

.

i. Position the attachment on the handle of iron. Decide which

outlet of attachment should use for the tube as the tube

can be pulled out from either way of the attachment. Find

the best position where can connect the tube straight to

the pipe. Be careful not to damage the inner wiring if

replace the tube inside of the attachment.

ii. Secure the attachment. Set the attachment on the handle

securely with clips and adhesive tape on backside of the

attachment. Refer to the following figure on the setting

position of the attachment and the guide pipe. Pay attention

on the setting angle of the guide pipe and the attachment.

4. Connect the Feeding

Nozzle

Insert the feeding nozzle into the feeding unit on the top of

the station, and secure it with screw.

NOTE

Securing the screw excessively may break the feeding

nozzle.

5. Connect the Mini-plug

Insert the mini-plug branching from the tube unit into the

jack of the station.

NOTE

Connect the mini-plug of foot switch to the station if you

use HAKKO MACH-

.

Nozzle

Guide Pipe

Securing Nut for Guide Pipe

Connection

Tube

Attachment

Clips

Guide Pipe Holder

Setting Up the HAKKO 373

Summary of Contents for 373
















Reviews: