HAKARU PLUS CORPORATION Tel. 81-6-6300-2195
05/12/16 TFL-B101Q DS (FL6)
Page 1
Smart mono-color digital bargraph
with four fully programmable set points for
monitoring, measurement, and control applications.
HAKARU PLUS CORPORATION
• Two 10 Amp Form C, and two 5 Amp Form A relays available
• Auto-sensing AC/DC power supply. For voltages between
85-265 V AC / 95-370 V DC (PS1)
or 15-48 V AC / 10-72 V DC (PS2).
• Optional isolated 16 bit analog output. User or factory
scalable to 4 to 20 mA, 0 to 20 mA or 0 to 10 V across any
desired span from ± one bar to the full scale range
• Provision to connect an external programming lockout switch.
• Optional NEMA-4 front cover.
• 24 V DC excitation is available to power external 4/20 mA
transmitters and 5 or 10 V DC excitation is available for
resistance bridge type sensors.
• The two 101 segment bargraph can be independently scaled.
• Bargraph center zero function.
• Four programmable setpoints.
• Relays activation can be selected to occur above (HI) or below
(LO) each setpoint.
• Decimal point setting.
Input Specs
: ..............Depends on range and function selected
A/D Converter
: ..........14 bit single slope
Accuracy
: ..................±(0.1% of r 1segment)
Temp. Coeff
.: .............100 ppm/°C (Typical)
Warm up time
:...........2 minutes
Conversion Rate
: ......10 conversions per second (Typical)
Bargraph Display
: .....
101 segment 4” vertical (std)
,
horizontal (optn),
red (std)
, green (optn),
one red one green (optn)
Polarity
: .....................Selectable center zero
Positive Overrange
: ..Bargraph display flashes
Negative Overrange
: First segment of bargraph display flashes
Relay Output
: ............Two 5 Amp Form A relays and Two
10 Amp Form C relays
Analog Output
: ..........Isolated 16 bit user scalable mA or V
OIC (mA out) ...........
4-20 mA @ 0 to 500Ω max loop resistance
OIV (volts out) ..........
0-10 V DC @ 500 Ω or higher resistance
Power Supply
: ...........AC/DC Auto sensing wide range supply
PS1 (std)
.................
85-265 VAC / 95-370 VDC @ 2.5W max 4.2W
PS2 .........................
15-48 VAC / 10-72 VDC @ 2.5W max 4.2W
Operating Temp
.: ......0 to 60°C
Storage Temp
: ...........–20°C to 70°C
Relative Humidity
: ....95% (non condensing)
Case Dimensions
: .....
3/32 DIN, Bezel: 36x144 mm(1.42”x5.69”)
Depth behind bezel: (4.64") 117.5 mm
Plus 10 mm (0.39”) for Right-angled
connector, or plus 18.3 mm (0.72”) for
Straight-thru connector, or plus 26.5 mm
(1.05”) for Push-On connector.
Weight
: .......................9.5 oz., 12 oz when packed
General Features
Input Module Compatibility
Specifications
Index
Software Features
Center Bar
for Dual Scale
Applications
(Tri-Color or
Mono-Color)
Left or Right Bar to match 6” Edgewise
Mechanical Meters with Left or Right
Pointers (Mono-Color only)
TFL-B101Q
OMI 220 Bargraph Meter
101 Segment LEDs
in a 9/64 DIN CASE
More than 50 different Plug-in I-Series Input Signal
Conditioners are approved for OMI 220 Family meters. Some
examples are shown on pages 12 - 15. Check with your local
distributors for an up to date listing.
Analog Scaling and Calibration . . . . . . . . . . . . . . . . . . . . 9
Case Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Center Zero Mode Scaling for Bipolar Inputs . . . . . . . 6-7
Component Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Glossary of Programming Symbols and Modes of
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Custom Scales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Functional Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Input Module Analog Calibration Procedures . . . . . . . . . . . .17
Input Module Compatibility . . . . . . . . . . . . . . . . . . . . . . . 1
Input Module Component Glossary . . . . . . . . . . . . . . . . . . .16
I-Series Input Signal Conditioning Modules . . . . . . 12-15
OMI 220 Family Bargraphs and Meters . . . . . . . . . . . . . . . . 17
One Point Quickset Rescaling and Calibration Procedure
6
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Opening the Case to Access Mode Select Headers . . . . . . . 4
Overview of Display Modes, Scaling Capabilities and
Operation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Panel Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setpoint Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Setting the Colors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Software Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Standard Display Mode Calibration Procedure . . . . . . . . 5
Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Two Point Quickset Scaling and Calibration . . . . . . . . .5,6
