background image

 

3

TN201AUV/TN131AUV Color TV Receiver 

 

Technical Notes 
   

I. General information 

TN201AUV 21 inch NTSC-M color TV receiver uses the single main chip 

LA76814, which is controlled by 12C bus, and the CPU chip is LC86F3348. 
This type of machine provides CCD and V-CHIP function and many other  

expended function, and enables high performance on the single PCB motherboard. 

 

II. Major technical data: 

1.  Frequency compound digital turning; 
2.  All channel CATV, AIRTV receiving; 

 

Band   AIRTV 

Channels  

CATV Channels  

Channel Range 
(MHz)  

L  

2~6  

2~6,A-5~A~3,A-2~B  

55.25~127.25  

M  

7~13  

C~KK  

133.25~361.25  

H  

14~69  

LL~125  

367.25~801.25  

 

3. Preset 125 Channels; 
4. NTSC-M system; 

5.  CCD and V-CHIP function; 
6.  Built-in AV input socket in the front panel; 

7.  Full-function infrared remote control; 
8. English/ French/Spanish on screen display; 

9.  Eight background color and foreground color; 
10. Direct program selector, program recall, program up/ down (skip programs 

which are set 'MEMORY=OFF'); 

11. Brightness, contrast, tint, sharpness, color and volume 64-steps control 

through 12c bus; 

12. Timer on/off, sleep off mode, power on/off and blank signal 10-minutes Auto-

off; 

13. Mute, blank signal auto-mute, auto-mute for programs which are set 

'MEMORY=OFF', and automatic search; 

14. Max. Audio output power large than 3w+3w; 
15. MTBF lowest limit not large than 20,000 hours; 
16. Power input 50/60Hz, 120

±

20V Ac; 

17. Antenna input resistance: 75

 (non-balanced style); 

18. Screen size: 54cm (flat square angle tube); 
19. Max. Power consumption: not more than 75W (120V AC/60Hz); 

20. Dimensions: 495X460X460.5 (mm); 
21. Weight: app. 21Kg. 

 

III Circuit working principle and functions: 

1.  Integrated circuit chip LA76814 

a)  This chip was created by SANYO in 1999. It is a NTSC-M system chip 

that integrated audio demodulator, filter, trap filter with the brightness 

delay line color decoder intermediate frequency filter. It is a highly 
integrated chip and yet has a well stability thus it requires less outer 

components for a color TV receiver. It also has the advance functions 

Summary of Contents for TN201AUV
















Reviews: