Haier AS12TB3HRA Service Manual Download

Page: 31 / 58

Service diagnosis

Domestic air conditioner

10.3.1 Thermistor or Related Abnormality

Indoor Display

★

ŶŶ(

Room temperature sensor failure

★

(

Heat-exchange sensor failure

Outdoor display

/('

flash 10 times

Defrost temperature sensor failure

/('

flash 11 times

Suction temperature sensor failure

/('

flash 12 times

Ambient temperature sensor failure

/('

flash 13 times

Discharge temperature sensor failure

Method of

The temperatures detected by the thermistors are used to determine thermistor errors

Malfunction
Detection

Malfunction When the thermistor input is more than 4.92V or less than 0.08V during compressor

D
Conditions

1RWH

The values vary slightly in some models

Supposed

Faulty connector connection

Causes

Faulty thermistor

Faulty PCB

Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or

else parts damage may be occurred.

Thermistor resistance check method

Remove the connector of the thermistor on the PCB, and measure the resistance of thermistor using tester.The

relationship between normal temperature and resistance is shown in the value of indoor thermistor.

Thermistor resistance check

Is it normal?

Yes

Is it normal?

Check the connector connection.

Replace the thermistor

Replace the indoor unit PCB

Correct the connection

Summary of Contents for AS12TB3HRA



























































Search results

Summary of Contents for AS12TB3HRA

Reviews:

Related manuals for AS12TB3HRA

Brands by name

Popular brands

Haier AS12TB3HRA, Service Manual

Search results

Summary of Contents for AS12TB3HRA

Reviews:

Related manuals for AS12TB3HRA

Brands by name

Popular brands