background image

 

Models 7180 and 7380 

Owner’s Manual

 and Installation Guide 

5/22/2019 

22 

Service Settings—ST, Cont. 

Operating Modes 

The controller has a Timer mode (Mode 1 

 Frequency and Mode 1 

 Days Of Week), a Demand Delayed mode 

(Mode 2), and a Demand Immediate mode (Mode 3). These modes are equipped with Capacity Guard

®

, which ensures 

that a supply of softened water will be available even with excessive water usage.  

Mode 1

—Timer Mode 

Select “Frequency” or “Days 

Of 

Week.”

 

When the appliance is in Mode 1 

 Frequency, it will regenerate based on the frequency that is set. For example, every 

day up to every 20 days. The days between regenerations can be set in the “Service Settings.” 

 

When “Frequency” is selected, the next screen displays “Regen Frequency.” Enter the desired n

umber of days (1

20) 

between regenerations. 

When “Days 

O

f Week” is selected, it will regenerate on a specific day(s) of the week. The next screen displays 

“Regeneration Time.” In “Customer Settings,” select the days on which you would like the unit to rege

nerate. 

Mode 2

—Demand Delayed Mode 

When the appliance is in the Patented Savematic Demand Delayed mode, it will regenerate based on the actual water 

usage and the total capacity of the appliance. The time that the regeneration takes place can be set, for example 

02:00am. Should the total capacity be depleted before the set regeneration time, a forced regeneration will occur. 

Mode 3

—Demand Immediate Mode 

When the appliance is in the Demand Immediate mode, it will regenerate based on water usage alone. Regeneration will 

occur when the capacity limit is reached. The time of regeneration cannot be set. Mode 3 is NOT recommended for 

residential use. 

72

–96 Hour Regeneration 

If this value is set to Yes, the appliance will be forced to regenerate every 96 hours unless a regeneration based on water 

usage occurs within the time interval. The value should always be set to Yes if iron is present in the water. 

Screen Power Saving Mode 

The screen powers off and goes black to save energy. When the screen is touched, it 

wakes up and displays the name and phone number of the dealer.  
 

 

 

Summary of Contents for MAXIMIZER 7180





























Reviews: