hager BODYGUARD-T Installation Instructions Manual Download Page 12 | Manualshive

Page: 12 / 12

hager BODYGUARD-T Installation Instructions Manual Download Page 12

BODYGUARD-T

Installation Instructions

I-EA00206

Rev 01, Rev Date: 05/08/2018

Page

12

of

12

Hager Companies 139 Victor Street, St. Louis, MO 63104 (800) 325-9995 www.hagerco.com

The sensor manufacturer cannot be held responsible for incorrect installations or inappropriate adjustments of the sensor/device; therefore, the sensor
manufacturer does not guarantee any use of the sensor outside of its intended purpose.
The sensor manufacturer strongly recommends that installation and service technicians be AAADM-certified for pedestrian doors, IDA-certified for
doors/gates, and factory-trained for the type of door/gate system.
Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor
system installation is compliant with local, national, and international regulations, codes, and standards.
Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer recommendations
and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must be performed during each service
call – examples of these safety inspections can be found on an AAADM safety information label (e.g. ANSI/DASMA 102, ANSI/DASMA 107, UL 325).
Verify that all appropriate industry signage and warning labels are in place.

INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS

«
...
10
11
12

Summary of Contents for BODYGUARD-T













Reviews:

No comments