Page 2 of 8
2916 Keypad
Installation Instructions
I-EA00080
Rev 9, Rev Date: 7/9/21
Always visit www.hagerco.com for the latest Installation Instructions
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995
Fig. 2 Wiring Pigtail Color Code
TO POWER SUPPLY
KEYPAD POWER
12 or 24 VOLTS
AC OR DC
}
+
-
RED
BLACK
NC
AUXILIARY RELAY
2 AMPS @ 28VDC MAX
}
NO
COM
ORANGE
WHITE
BLACK
MAIN RELAY
5 AMPS @ 28VDC MAX
}
NO
COM
NC
ORANGE
WHITE
YELLOW
QuickStart Programming
You must first enter programming mode to perform any function. The yellow indicator will blink slowly showing that the 2916 is in
programming mode. Use the option codes to program each function. After the new data entry is complete for each function , the
yellow indicator will flash quickly while the data is being stored and the green indicator will light briefly if the programming has
been accepted. The red indicator will light if any programming data is entered incorrectly or the function is rejected. If a red
indicator is seen, the entire function (option code + data) will have to be fully re-entered. The keypad will remain in programming
mode until # is pressed or after 30 seconds of inactivity.
**
Test your new user code
Enter user code ‘9876#’. The green indicator should illuminate, the
main relay should activate and the door should unlock for 5 seconds.
BLACK
PINK/SALMON
GREEN
GRAY
BLACK
VIOLET
BLACK
BLUE
DOOR POSITION
SWITCH
[N/C]
REQUEST-TO-EXIT
SWITCH
[N/O]
GROUND
OUTPUT #4
OUTPUT #3
GROUND
SENSE
REQUEST TO EXIT
GROUND
E
1
E
8
E
7
E
6
E
5
E
4
E
3
E
2
C
NO
C
NC
NO
AUXILIARY OUTPUTS
100mA MAX TO COMMON
{
*
*
NOT USED
KEYPAD
POWER
WIRE
HARNESS
(E1-E8)
MAIN
RELAY
AUXILIARY
RELAY
ANTI-TAMPER
SWITCH
BACK
JP1
E1
E8
JP2
Grn Wire
To earth ground
CAUTION
IF THE UNIT IS AC POWERED, MAKE SURE
THAT THE SECONDARY OF THE SYSTEM IS
ISOLATED FROM EARTH GROUND
!
!
RED/GREEN
POWER/ACCESS
INDICATOR
YELLOW
“PROGRAM”
INDICATOR
KEYPAD
FRONT
Deleting a user code
To delete a user:
Step 1. Enter:
#9# 123456#
Enter the program mode (default master code)
Step 2. Enter:
02# 9876# 9876#
User PIN code 9876 has been deleted.
Step . Enter:
#
Exit programming mode
**
Adding additional user codes
Once the code length and relay time have been set you do not need to set them each time
you additional users.
To add additional users:
Step 1. Enter:
#9# 123456#
Enter the program mode (default master code)
Step 2. Enter:
01# 2222# 2222# 1#
PIN code ‘2222’ is assigned to
momentarily activate the main relay
Step 3. Enter:
01# 2580# 2580# 10#
PIN code ‘2580’ is assigned to
toggle (on/off) the main relay
Step 4. Enter:
#
Exit programming mode
**
Program the first user code
Step 1. Enter:
#9# 123456#
Enter the program mode (default master code)
Step 2. Enter:
03# 4#
Set the entry code length to 4 digits
Step 3. Enter:
21# 5#
Set the main relay activate time to 5 sec.
Step 4. Enter:
01# 9876# 9876# 1#
PIN code ‘9876’ is assigned to
momentarily activate the main relay
Step 5. Enter:
#
Exit programming mode
**
