Page 1 of 8
2916 Keypad
Installation Instructions
I-EA00080
Rev 9, Rev Date: 7/9/21
Always visit www.hagerco.com for the latest Installation Instructions
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995
The
2916
Indoor/Outdoor Keypad is a surface-mount digital keyless
entry system designed for access control applications. The backlit
keys are bright and easy-to-read. A heavy cast vandal resistant
housing design with mounting plate allows the 2916 to be mounted
on a rugged surface or on a standard single-gang electrical box.
The 2916 has a capacity of 500 users. Users can be assigned to use
4 to 6 digit PIN codes. An authenticated access can be programmed
to activate one or both of the onboard relay outputs.
The timed “anti-passback” feature prevents using the same
credentials twice before a programmed waiting period has
elapsed.
Two long lasting solid state LED indicators show the status of the
system. The left bi-color indicator lights red to indicate power, then
solid green when a relay is active (access grant, etc.). The right
indicator flashes yellow to indicate that the keypad is in programming
mode.
An internal sounder can be programmed to beep each time a key is
pressed or when an output is activated. An internal jumper sets the
sounder volume high or low.
The
SENSE
input can be configured two ways through
programming . When configured for “Door Sense”, the input is wired
to a normally closed door position switch to detect when the door is
opened or closed. Forced entry or door ajar situations can then be
detected. The “Auto-relock” feature can also be used to turn off the
Main Relay output immediately when the door is closed after access
has been granted to prevent “tailgating”.
When the
SENSE
input is configured for “Inhibit”, the input can be
wired to a normally open “service” switch or automatic timer that will
disable access while the switch is closed.
The
REQUEST-TO-EXIT
input can be wired to a normally open
pushbutton to provide codeless activation of the Main Relay,
Auxiliary Relay, Output #3 or Output #4 (user programmable).
The
ALARM SHUNT
signal is available when access is granted.
This signal can be programmed to activate any of the relays or solid
state outputs to shunt alarm contacts on the access door/gate
preventing the triggering of an alarm when an authorized access
occurs.
The 2916 is powered from a 12 or 24V AC or DC source. The non-
volatile EEPROM memory retains entry codes and programming
when power is removed. An internal jumper is provided to reset the
master code. The Main Relay has a 5 Amp capacity. The Auxiliary
Relay has a 2 Amp capacity. Two solid state outputs, capable of
sinking 100 mA to common are programmable for alarm shunting, or
to signal forced entry, door ajar, keypad lockout, request-to-exit, and
keypad active conditions.
INSTALLATION INSTRUCTIONS
2916 Keypad
SPECIFICATIONS
Mechanical
Dimensions: 3.00" W x 5.75" H x 1.375" D
(1.4375” wall projection)
Electrical
Input Voltage: 12/24 Volts AC or DC
Operating Current: 30 mA typical, 150 mA max
Output Ratings
Main Relay: Form “C” 5 Amps @ 28 Volts max
Auxiliary Relay: Form “C” 2 Amp @ 28 Volts max
Type: Solid state outputs (Outputs #3 & #4)
Short-to-common 100 mA @ 24 VDC maximum
Environmental
Temperature: -4°F to 140°F (-20°C to 60°C)
Humidity: 5% to 95% non-condensing
FEATURES
Keypad programmable
500 user codes
4 to 6 digit user codes
4 independent outputs
4 independent timers
2 Form C relay contacts
2 solid state open collector outputs
Program entry codes to activate one or
two relays
Disable input
Door sense input
Request-to-exit/Reception input
Keypad tamper lockout
Timed anti-passback
Anti-tailgate
Two LED status indicators
Tactile key feel
Audible code entry verification
12V or 24V, AC or DC operation
