hager 2916 Installation Instructions Manual Download Page 4

Page: 4 / 8

Page 4 of 8

2916 Keypad

Installation Instructions

I-EA00080

Rev 9, Rev Date: 7/9/21

Always visit www.hagerco.com for the latest Installation Instructions

HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995

FACTORY DEFAULTS

Master Programming Code………..………………….….…...123456
Entry Code Length……………………………………….……..4 digits
Request-to-exit Output Relay………………………..........No Output
Alarm Shunt Output….………………………………….........Disabled
Forced Entry Output……………………………..…………No Output
Door Ajar Output…………………………………..…….….No Output
Main Relay On Time…………………………………..…..02 Seconds
Auxiliary Relay On Time…………………………….....…02 Seconds
Solid State Output #3 On Time………………………......02 Seconds
Solid State Output #4 On Time…………………………..02 Seconds
Door Sense/Inhibit Input…………………………...…………....Inhibit
Keypad Lockout Output………………………………..…….Disabled
Keypad Active Output………………………………..…..…..Disabled
Beeper Sounds When Key Pressed……………………...………Yes
Beeper Sounds During Relay #1………………………..…...…….No
Beeper Sounds During Relay #2……………………………...…...No
Beeper Sounds During Output #3……………………………........No
Beeper Sounds During Output #4……………………………........No
Keypad Lockout Count……….………......….3 Tries Before Lockout
Anti-Passback Time………………..……...……….No Anti-Passback
Auto-Relock…………………………………...………….………….On

BASIC PROGRAMMING

When the 2916 is in Programming Mode the yellow indicator will
blink slowly.  After a programming command is selected, the
yellow indicator will flash rapidly while the keypad is waiting for
user input data.  The green indicator will light if the data is
accepted.  The red indicator will light if any programming data is
entered incorrectly, and the command will have to be fully re-
entered.

Entering Programming Mode

The 6-digit Master Programming Code (default = 123456) is used
to enter Programming Mode.

Press: # 9 # Master Code #

Master Code = the current 6-digit Master Programming Code

Setting Entry Code Length

Default: 4 digits

Press: 03 #

Length

Length = 1-6 for entry code length

Note:

If the Entry Code Length is going to be changed from the factory

default of 4 digits, make this change first before programming any entry
codes.

Adding a New User PIN Code

Press: 01 #

Code

Code # Relay #

Code

=The new entry code: 1-999999, depending on code length

Relay

=Relay output entry code will activate:

1=Main Relay 2=Auxiliary Relay 3=Both Relays
10=Relay #1, toggled 20=Relay #2, toggled 30=both Relays
toggled
12=Relay #1 toggled; Relay #2 timed open
21=Relay #1 timed open; Relay #2 toggled

The green indicator will light momentarily when the new code is
accepted. The green indicator will light when the new code is
accepted. If the user number already exists or an entry error has
been made, the red indicator will light. Delete the user and re-
enter the new information again.

Note:

Leading zeros (zeros before the code number, i.e.0001)

do not need to be entered when programming a new code. The
2916 will internally add any zeros to fill digits determined by the
entry code length setting. Leading zeros will have to be entered
by the user when entering their code to gain access.

Erasing a Single User

Press: 02 #

Code

Code = The PIN code to be deleted

The yellow indicator will flash quickly while the 2916 erases the
PIN code from memory. The green indicator will light when the
code is erased.

Output Toggle Mode

When an output is programmed for Toggle Mode, the output
alternates from OFF to ON or from ON to OFF each time it is
accessed. When an output is toggled on, the green LED remains
solid until toggled off.

The rules for a toggle output are:



If the output is OFF, entering a

toggle

code will turn ON the

selected relay. The selected relay will stay ON until the next
activation of a toggle code.



If the output is ON, entering a

toggle

code will turn OFF the

selected relay. The selected relay will stay OFF until the
next activation of a toggle code.



*An authorized PIN or REX input programmed to
momentarily activate that same relay

WILL NOT

reset the

relay to its normal state.

Re-entering a Command After a Mistake

If the red indicator lights, signaling an incorrect entry, or an
incorrect key is pressed during programming, to clear the
keypad and re-enter the command:

Press:

9 #

Exiting Programming Mode

Press:

The red indicator will light after exiting Programming Mode

Note:

The 2916 will automatically exit Programming Mode

after 30 seconds of inactivity

See the following example that sets entry codes 1234 for normal
operation and 5678 for toggle operation.

Press: 01 # 1234 # 1234 # 1 #

01=Programming Step; 1234=Entry Code; 1=Main Relay

Press: 01 # 5678 # 5678 # 20 #