Installation
5.52.291.00.01.01
13
6.3.1 Wire
rope
fastening
The wire rope is fastened with retainer key. The retainer key is attached to the consignment for winches
supplied without wire rope.
Push the wire rope through the hub of the
flanged wheel and through the key pocket.
Pull some centimeters out.
Wrap it completely round the retainer key (1)
Place it back into the key pocket.
Illustration 2
By pulling the wire rope, the retainer key gets
stuck into the pocket and locks the wire rope
safely.
It may be necessary to insert the retainer key a
little bit into the hub with a soft tool before the wire
rope can be loaded.
Illustration 3
Pos: 10.2.3.3.1.2 /1_HADEF/6--MONTAGE/Winde + Seilzug/Drahtseil/*05.Seilbefestigung*/42/87/2. 42/87 - Ablaufrichtung A @ 2\mod_1286894125345_52.docx @ 16112 @ @ 1
The wire rope feed out direction is determined by
the motor.
See chapter "Installation".
Illustration 4
Pos: 10.2.3.4.1 /1_HADEF/6--MONTAGE/Winde + Seilzug/Drahtseil/*Allgmein*/06.Seilaufwicklung-Alle @ 0\mod_1175065250946_52.docx @ 2900 @ @ 1
6.4
Winding up of wire rope
The wire rope must always be winded up tensioned. When the last wire rope layer is winded onto the drum,
the flanged wheel must exceed the top layer by at least 1 1/2 times of the wire rope diameter.
Pos: 10.2.3.4.2 /1_HADEF/---ALLGEMEIN/Hinweise/Winden/HINWEIS - 2 Wicklungen auf Trommel @ 0\mod_1177330646284_52.docx @ 5254 @ @ 1
NOTICE!
According to DIN 15020 regulations and to the accident prevention regulations BGV D8, the wire rope
length must be chosen so that at least 2 rope layers remain on the drum when the wire rope is unwinded.
Pos: 10.2.4.1.1 /1_HADEF/6--MONTAGE/Winde + Seilzug/Seilablenkung/*Seilablenkung*/07.Seilablenkung-allgemein @ 0\mod_1175065654558_52.docx @ 2913 @ @ 1
6.5
Wire rope deflection
Wire rope pulleys must be installed in a
position centrically to the rope drum.
In order to ensure correct winding up of the
wire rope on the drum, the max. wire rope
deflection angle must not be exceeded.
maximum wire rope deflection angle
4° for standard wire ropes
2° for non-twisting resp. twist-resistant wire
ropes
The minimum dimension (M) from the drum
until the middle of the pulley must be adhered
to.
Illustration 5
Pos: 10.2.4.1.2 /1_HADEF/---ALLGEMEIN/Hinweise/Winden/HINWEIS - Umlenkrolle Abstand M - Richtwerte @ 0\mod_1177332963920_52.docx @ 5276 @ @ 1
NOTICE!
Should the drum be extended and for some models with limit switch, the distance "M" must be increased.
Standard values:
15x 1/2 drum length for standard wire ropes
30x 1/2 drum length for twist-resistant or non-twisting wire ropes
Pos: 10.2.4.2 /1_HADEF/6--MONTAGE/Winde + Seilzug/Seilablenkung/*Seilablenkung*/08.Umlenkrolle-Abstand-Tabelle-42/87 @ 1\mod_1245761642571_52.docx @ 11004 @ @ 1
