UNPACKING
When unpacking your new machine, make sure following items are there before discarding the
packing material:
•
There should be 2 brushes in the water tank.
•
The upper tape plate is proper fixed by packing material but may have been dislodged in shipping.
Remove all fixing material before using the machine.
SETTING UP
•
In case the upper tape plate has been dislodged in shipping, replace as follows: With the center
slot towards the front of the machine slide underneath the feed wheel shaft from the rear until
the cut-out portions on the sides are above the retaining buttons. Drop the plate and slide
forwards that the end of the plate is underneath the rod, just to the rear of the shear and the
back end is under the buttons.
•
Remove tank and brushes. Wash brushes thoroughly in warm water and soap or mild detergent.
Put brushes into the water tank. Please note: Both brushes are beveled. Make sure each brush is
positioned with the longest bristles towards the front of the tank. Put back tank and brushes into
the machine.
•
Fill bottle with water and put it into the bottle guides while the spout of the bottle is in the tank.
Set the correct water level (for adjusting see WATER LEVEL).
•
Adjust roll guides inside the rear of the machine to fit the width of the tape (see ROLL GUIDE
ADJUSTMENT).
•
Unwind approximately 25cm of the gummed tape. Position the roll into the basket while the
unwinded end of the roll points to the front of the machine (gummed side down). Move the
leading edge of the tape underneath the upper tape plate. Ensure the tape has passed the upper
feed wheel.
•
Set pressure plate weight and temperature for the top heater.
ADJUSTMENTS
•
ROLL GUIDE ADJUSTMENT: The tape roll guides in the tape basket should be properly set for the
widths of tape being dispensed. The roll of tape should preferable be centred between the frames
by confining the tape loosely between the spring loaded spacers on the tie rods.
To set the roll guides in position, lift them out, move to the desired position and re-insert.
•
WATER LEVEL ADJUSTMENT: The amount of water required for proper moistening of different
grades and types of tape will differ. Heavier glues on reinforced tapes will normally require a
higher
water
level.
Lighter
tapes
require
less
water
and
a
lower
level.
The water level is controlled by the position of the front water bottle bracket. To adjust the water
level loosen the two screws on the bottle bracket, move to desired position and tighten both
screws.
INSTRUCTIONS FOR USE
Summary of Contents for Better Packages TERZETT 754
