Habasit PMR-07 General Manual Use And Maintenance Download Page 27 | Manualshive

Page: 27 / 68

Habasit PMR-07 General Manual Use And Maintenance Download Page 27

Habasit Italiana S.p.A.
Vittorio Veneto 31029 (TV)
Tel.: ++39(0)438.9113
Fax. ++39(0)438.200545

Regulating Unit PMR-07

Author:

A.T. / KM

INSTALLATION

Edition: 04/2006

Page

C-3

Replaces: 10/2005

C.2

PACKING AND HANDLING

ATTENTION

The movement of the packaging and machinery should be carried out by authorized operators.
Suitable equipment must be used to move the regulating unit, with adequate strength to deal
with its weight and bulk.
The equipment must be completely disconnected before it is transported.
There are two handles at the side for lifting the equipment.
Never use the electrical cables connected to the equipment to lift it.
When unpacking, check that no small parts remain in the case, and carefully check the general
conditions.
Packing materials (wood, nails, plastic, barrier bags, etc.) can be sources of danger and should
be placed in collection points, especially if polluted or non-biodegradable.
Concerning disposal of packing materials, the user must observe the current laws of the country
of installation.

IMPORTANT

REPORT ANY DAMAGE NOTED ON THE REGULATING UNIT AT DELIVERY TO THE

CARRIER AND SUPPLIER.

ATTENTION

ALL HANDLING OPERATIONS OF THE REGULATING UNIT MUST BE PERFORMED SLOWLY

WITHOUT ANY SUDDEN MOVEMENTS, TO AVOID DAMAGING PERSONS AND MATERIALS.

Regulating Unit PMR-07

«
...
25
26
27
28
29
...
»

Summary of Contents for PMR-07





































































Reviews:

No comments