H3C WA510H Installation Manual Download Page 11 | Manualshive

Page: 11 / 19

background image

5

Installing the AP

1.

Align the installation hole in the rear of the AP with the standout on the mounting bracket.

Figure 4 Aligning the AP installation hole with the mounting bracket standout

2.

Push the AP onto the mounting bracket, and then slide it down until it is fully engaged. Then
secure the AP to the bracket by using the M2.9 × 4 security screw, as shown in

«
...
9
10
11
12
13
...
»

Summary of Contents for WA510H




















Reviews:

No comments

Related manuals for WA510H

Brand: Cambium Networks Pages: 3

Brand: Cambium Networks Pages: 68

Brand: Laird Pages: 24

Brand: Laird Pages: 6

Brand: Ubiquiti Pages: 16

Brand: Ubiquiti Pages: 24

Brand: Ubiquiti Pages: 38

Brand: Ubiquiti Pages: 14

Brand: Ublox Pages: 151

Brand: Ubiquiti Pages: 2

Brand: LevelOne Pages: 33

Brand: sauter Pages: 8

STEVAL-SPBT4ATV3

Brand: ST Pages: 9

Brand: B-Link Pages: 14

Brand: Ruckus Wireless Pages: 4

Brand: Sena Pages: 82

Brand: ZyXEL Communications Pages: 109

Brand: FS Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands