H3C WA510H Installation Manual Download Page 18

Page: 18 / 19

Mark Status

Description

Uplink LED

Off

No link is present on the port.

Steady yellow

The negotiated rate is 10/100 Mbps.

Flashing yellow

The uplink port is sending or receiving data at 10/100
Mbps.

Steady green

The negotiated rate is 1000 Mbps.

Flashing green

The uplink port is sending or receiving data at 1000
Mbps.

Ethernet port
LED

Off

No link is present on the port.

Steady yellow

The negotiated rate is 10/100 Mbps.

Flashing yellow

The Ethernet port is sending or receiving data at 10/100
Mbps.

Steady green

The negotiated rate is 1000 Mbps.

Flashing green

The Ethernet port is sending or receiving data at 1000
Mbps.

Ports

The AP provides the following ports:

•

One console port.

•

Four 10/100/1000 Mbps copper Ethernet ports.

•

One power port.

•

Two Pass Through ports.

•

One Uplink/PoE In port.

•

One USB port.

NOTE:

The AP also has a reset button.

Summary of Contents for WA510H




















Search results

Summary of Contents for WA510H

Reviews:

Related manuals for WA510H

Brands by name

Popular brands

H3C WA510H, Installation Manual

Search results

Summary of Contents for WA510H

Reviews:

Related manuals for WA510H

Brands by name

Popular brands