H3C WA2200 Series Installation Manual Download Page 32

Page: 32 / 42

Figure 31

LEDs on the WA2210-AG/WA2220-AG

Table 6

Description of LEDs on the WA2210-AG/WA2220-AG

LED

Color

QTY

Meaning

POWER

Green

Displays the power supply status:



On: The power supply is normal.



Off/flashing: The power supply is not connected or well

connected, or works abnormally.

LINK/ACT Green

Displays the link status of the Ethernet interface:



On: The link on the Ethernet interface is up.



Off: The link on the Ethernet interface is down.



Flashing: Data is being transmitted or received.

11a

Green

Displays the wireless link status:



Off: The wireless link is not initialized or the link is faulty.



Flashing slowly: The wireless link is normal.



Flashing quickly: Data is being transmitted or received.

11b/g

Green

Displays the wireless link status:



Off: The wireless link is not initialized or the link is faulty.



Flashing slowly: The wireless link is normal.



Flashing quickly: Data is being transmitted or received.

POWER

LINK/ACT

11a

11b/g

Summary of Contents for WA2200 Series











































Search results

Summary of Contents for WA2200 Series

Reviews:

Related manuals for WA2200 Series

Brands by name

Popular brands

H3C WA2200 Series, Installation Manual

Search results

Summary of Contents for WA2200 Series

Reviews:

Related manuals for WA2200 Series

Brands by name

Popular brands